Vortec Heads on Pre 87 350's
#11
Registered
Join Date: Jun 2007
Posts: 454
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
Are they clearenced for a boat or a car? There is a difference there are threads about people putting car engines into a boat and them blowing up. The exhaust valve clearence and main and rod bearing clearence are different. GM has marine engines and auto engines. be sure.
#12
Pirate of the Chesapeake
![](https://www.offshoreonly.com/forums/images/icons/gold_member_star.gif)
Join Date: Aug 2006
Location: North Point Creek, Md.
Posts: 4,330
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
John
#13
Gold Member
![](https://www.offshoreonly.com/forums/images/icons/gold_member_star.gif)
Join Date: Oct 2005
Location: Olmsted Falls,Ohio Marblehead,Oh
Posts: 11,636
Likes: 0
Received 209 Likes
on
133 Posts
![Default](/forums/images/icons/icon1.gif)
Are they clearenced for a boat or a car? There is a difference there are threads about people putting car engines into a boat and them blowing up. The exhaust valve clearence and main and rod bearing clearence are different. GM has marine engines and auto engines. be sure.
A 350 car engine and boat engine is clearanced the same.
I tore down my 88 merc 350CI and found nothing different besides the merc had a mercruiser tag rivited to it. same pistons crank and rods as the 88 Roller c am 350 I installed from my friends Camaro. I looked up all part numbers to be sure, both had the same parts, and same balance.
Intake and Exhaust valve clearence has to do with the cam specs and heads used, I ran a decent size cam in my old boat with edelbrock heads and had TONS of clearenc intake and exhast, it was a ZZ9 GM performance cam.
#14
Registered
Thread Starter
Join Date: May 2007
Posts: 66
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
The 92 Merc 454 mag I just had rebuilt also had all the same internals as a 454 HO crate motor. Part #s the same. I think the main differences on a marine engine are gaskets and external parts like oil pan, water pump, fuel pump, carb, and distributer and thats to be Coast Guard approved.
I think Alphas are under rated and can handle more than 300 hp. I know Sea Ray built lots of Pachangas w/ 330 hp 454s and Alpha drives.
I think Alphas are under rated and can handle more than 300 hp. I know Sea Ray built lots of Pachangas w/ 330 hp 454s and Alpha drives.
#15
Registered User
Join Date: Feb 2005
Location: St. louis, East Sider
Posts: 891
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
I just built a 89 5.7 merc with vortec heads w/ bigger valves and lunati voodoo cam (don't remember the specs off the top of my head). Didn't dyno but it picked up 6 mph in a 19-20' chapparal villain over the 270hp.
#16
Registered
Join Date: Sep 2005
Location: NIAGARA FALLS ONTARIO
Posts: 36
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
When We Build Small Block 383's We Run The Same Clearence As Street Engines Except For Rings We Run The Same Gap As Nitrous. Havent Run Into Any Problems. Also We Run Dart Heads And They Advertize For Marine Or Street Use.
Hope This Helps.
Hope This Helps.