Nauti by Nature Cigarette 38 Top Gun Refresh!!
03-20-2013, 12:01 PM
#71
Registered
Thread Starter
Join Date: Jun 2011
Posts: 863
Likes: 0
Received 0 Likes
on
0 Posts
No this will be our first time on the run... I really feel like we will make it! I feel really good about the machine work now! Joe addressed all my concerns from Nortech (Daryl Hameetman's) previous machine work that was done
03-20-2013, 01:31 PM
#72
Registered
Join Date: May 2010
Location: Cedar Springs MI
Posts: 574
Likes: 0
Received 0 Likes
on
0 Posts
03-20-2013, 10:33 PM
#74
Registered
Thread Starter
Join Date: Jun 2011
Posts: 863
Likes: 0
Received 0 Likes
on
0 Posts
OK, we have the rest of the valve train parts from Bob Madara!!
These are Custom Billet Steel Gen 6 (4,7,3,2) Swap Fire Cams!! The Firing order was changed to smooth out the harmonics in the bottom end. The new firing order is 1 8 7 2 6 5 4 3. You can see cylinders 4 7 3 2 were swapped from the original FO.
Yes this stuff is going into Mark IV Blocks!! I will show you how it's done when I get the blocks back from Fast Forward Marine/Race Engines!
Gen 6 Cams, Billet Double Roller Gen 6 (9 Position) Timing Chains, ARP (Metric) Cam/Timing Chain Bolts, Gen 6 Cam Retainer Plate, Correct Distributor Gear for the Billet Steel Cam Cores!!
Step Nose Gen 6 Billet Steel Cams
Custom Cam Card. 540 Cubic Inch Supercharged!
Billet Gen 6 Double Roller Timing Chains! 9 Position Crank Sprocket to fine tune your Cam Degree In
Made in USA!
Double Roller (2 Chains!)
Torrington Roller Bearing rides on the Cam Retaining Plate!
Gen 6 Cam Retaining Plates & Correct GM Bolts
Correct Distributor Gears for the Billet Steel Cam
These are Custom Billet Steel Gen 6 (4,7,3,2) Swap Fire Cams!! The Firing order was changed to smooth out the harmonics in the bottom end. The new firing order is 1 8 7 2 6 5 4 3. You can see cylinders 4 7 3 2 were swapped from the original FO.
Yes this stuff is going into Mark IV Blocks!! I will show you how it's done when I get the blocks back from Fast Forward Marine/Race Engines!
Gen 6 Cams, Billet Double Roller Gen 6 (9 Position) Timing Chains, ARP (Metric) Cam/Timing Chain Bolts, Gen 6 Cam Retainer Plate, Correct Distributor Gear for the Billet Steel Cam Cores!!
Step Nose Gen 6 Billet Steel Cams
Custom Cam Card. 540 Cubic Inch Supercharged!
Billet Gen 6 Double Roller Timing Chains! 9 Position Crank Sprocket to fine tune your Cam Degree In
Made in USA!
Double Roller (2 Chains!)
Torrington Roller Bearing rides on the Cam Retaining Plate!
Gen 6 Cam Retaining Plates & Correct GM Bolts
Correct Distributor Gears for the Billet Steel Cam
Last edited by mmb; 03-21-2013 at 07:18 AM.
03-23-2013, 11:24 PM
#75
Registered
Thread Starter
Join Date: Jun 2011
Posts: 863
Likes: 0
Received 0 Likes
on
0 Posts
Pressure Tested the Chillers Tonight!! Just have to polish them out now... 
I used my Cat Hydraulic Test Equipment..... Modified it to use air instead of Hyd Fluid.
Test Fitting in the Chiller
Pressure tester with a 35lb Gauge hooked up
Put the Chillers under water
Put Air into the Chiller
Held 31psi for 2 hours!! Good to go!!
I used my Cat Hydraulic Test Equipment..... Modified it to use air instead of Hyd Fluid.
Test Fitting in the Chiller
Pressure tester with a 35lb Gauge hooked up
Put the Chillers under water
Put Air into the Chiller
Held 31psi for 2 hours!! Good to go!!
03-27-2013, 07:28 AM
#79
Registered
What blowers are you running? what snouts? Can you post detail pics of your blower pulley, and serpentine pulleys, and setup? Also, the blower belt tensioner?
I was looking over mine last night, I need to revamp some things and needed some ideas. Who makes a nice tensioner setup for the 420 Megablower???
Thanks.
I was looking over mine last night, I need to revamp some things and needed some ideas. Who makes a nice tensioner setup for the 420 Megablower???
Thanks.
