Offshoreonly.com

Go Back  Offshoreonly.com > Technical > Do It Yourself, Boating on a Budget
Dyno Results: 502 w/ AFRs >

Dyno Results: 502 w/ AFRs

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices

Dyno Results: 502 w/ AFRs

Thread Tools
 
Old 05-17-2014, 09:56 AM
  #61  
VIP Member
Platinum Member
Thread Starter
 
Join Date: Jun 2009
Location: East Greenwich, RI
Posts: 937
Received 75 Likes on 36 Posts
Default
Originally Posted by I'CE
did the 548 near 665hp? thanks so much on 242's engine builds your good to go, now he must be careful on the sticks. any prop talk yet ? or just spin em.
Considering I never saw more than 4950 RPMs with my BBlades labbed M+ 23P 3 blades (1.36 GR), I want to see more RPM with the same prop. Bob's target was 5700. I'd be very happy with 5400-5500.

BTW - Just went 188 MPH on the MagLev in Shanghai.
[ATTACH=CONFIG]523509[/ATTACH]
Attached Thumbnails Dyno Results: 502 w/ AFRs-image.jpg  
242LS is offline  
Reply
Old 05-17-2014, 11:50 AM
  #62  
Registered
 
Join Date: Jul 2004
Location: chicago
Posts: 11,332
Received 71 Likes on 39 Posts
Default
Originally Posted by lil red
I did on a 548 last week with the same heads and quench, same style piston. Power didn't go up, actually lost some at 36* and egt's only dropped a few degrees. Most of these guys fill up on the road with 93 octane which I prefer, more additives etc. less chance of getting a bad tank of fuel. So I don't mind running a little hotter plug, a little lower air fuel and the temps fall in line. Without fouling plugs or poor idling.
Reason I asked is the shorter 4" stroke might have liked a little more timing. I am with ya on the fuel stuff. A lean marine engine is a burnt marine engine! Either way, congrats on a nice build buddy!
MILD THUNDER is offline  
Reply
Old 05-17-2014, 12:36 PM
  #63  
Banned
 
Join Date: Jun 2013
Location: AZ
Posts: 1,014
Likes: 0
Received 0 Likes on 0 Posts
Default
Did you go with a a18726543 firing order, or standard BBC?
Borgie is offline  
Reply
Old 05-17-2014, 05:13 PM
  #64  
Registered
 
Rookie's Avatar
 
Join Date: Jan 2003
Location: Grand Rapids, MI
Posts: 5,753
Received 1,249 Likes on 604 Posts
Default
Originally Posted by Borgie
Did you go with a a18726543 firing order, or standard BBC?
I'm assuming if he used Bobs cam it is the 2/3 4/7 swap. I'm pretty sure they are designed off the new firing order mine from Bob were.
Rookie is offline  
Reply
Old 05-17-2014, 05:18 PM
  #65  
Banned
 
Join Date: Jun 2013
Location: AZ
Posts: 1,014
Likes: 0
Received 0 Likes on 0 Posts
Default
Originally Posted by Rookie
I'm assuming if he used Bobs cam it is the 2/3 4/7 swap. I'm pretty sure they are designed off the new firing order mine from Bob were.
Yeah seems he does quite a few of those these days, but not all. Mine is as well, thx!
Borgie is offline  
Reply
Old 05-17-2014, 06:13 PM
  #66  
Registered
 
Join Date: Jul 2009
Location: Taunton Ma
Posts: 8,527
Received 700 Likes on 342 Posts
Default
The 548's cam is a bit more conservative. It was originally selected for a boat with reversion issues. It made 635 and 660tq
Unlimited jd is offline  
Reply
Old 05-17-2014, 06:14 PM
  #67  
Registered
 
Join Date: Jul 2004
Location: chicago
Posts: 11,332
Received 71 Likes on 39 Posts
Default
Originally Posted by lil red
The 548's cam is a bit more conservative. It was originally selected for a boat with reversion issues. It made 635 and 660tq
Nice numbers. Same 305cc as cast AFR with CNC chambers?
MILD THUNDER is offline  
Reply
Old 05-17-2014, 07:21 PM
  #68  
VIP Member
Platinum Member
Thread Starter
 
Join Date: Jun 2009
Location: East Greenwich, RI
Posts: 937
Received 75 Likes on 36 Posts
Default
Originally Posted by Rookie
I'm assuming if he used Bobs cam it is the 2/3 4/7 swap. I'm pretty sure they are designed off the new firing order mine from Bob were.
Standard. We had a mixup - so it will be swapped next time it gets open heart surgery (I hope that doesn't happen for a long time).
242LS is offline  
Reply
Old 05-17-2014, 08:25 PM
  #69  
Registered
 
Join Date: Jul 2004
Location: Angola NY
Posts: 432
Received 12 Likes on 7 Posts
Default
What is the top end valve train refresh interval on a cam that size?
tbanzer is offline  
Reply
Old 05-17-2014, 10:11 PM
  #70  
Registered
 
Join Date: Jul 2009
Location: Taunton Ma
Posts: 8,527
Received 700 Likes on 342 Posts
Default
Originally Posted by MILD THUNDER
Nice numbers. Same 305cc as cast AFR with CNC chambers?
Yes same heads
Unlimited jd is offline  
Reply



Advanced Search

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.