Cutting up ST, resin the exposed edges?
#1
Registered
Thread Starter
Join Date: Aug 2006
Location: IAD/FLL
Posts: 2,090
Likes: 0
Received 0 Likes
on
0 Posts
Cutting up ST, resin the exposed edges?
From all the Silent Thunder mod threads I've read, I don't recall anyone mentioning whether they slapped a little resin on the newly exposed edges? I'm about to cut 3" or 4" holes just underneath each outlet and might install floor drain covers typically found in CC floors (might Krylon the drain covers too; black maybe?). I think it'll make for a cleaner look, and these ST "drains" will hopefully let the exhaust-laiden water out before staining my outlets.
I've already cut the baffles out...
I've already cut the baffles out...
#2
Registered
From all the Silent Thunder mod threads I've read, I don't recall anyone mentioning whether they slapped a little resin on the newly exposed edges? I'm about to cut 3" or 4" holes just underneath each outlet and might install floor drain covers typically found in CC floors (might Krylon the drain covers too; black maybe?). I think it'll make for a cleaner look, and these ST "drains" will hopefully let the exhaust-laiden water out before staining my outlets.
I've already cut the baffles out...
I've already cut the baffles out...
#3
Registered
Thread Starter
Join Date: Aug 2006
Location: IAD/FLL
Posts: 2,090
Likes: 0
Received 0 Likes
on
0 Posts
Hey Mike! I think it sounds perfect. More rumble/throaty, but not so obnoxious to piss off the neighbors. I've only been in the driver's seat while on plane, and I can't say that it makes more sound if you have your head in the wind. Maybe just a tad bit more if you duck down.
Also, this is with stock exhaust. I've got a set of RevMarine pieces still to install. I think with anything aftermarket, we'll get a little more rumble.
Any thoughts on sealing the cut pieces?
Also, this is with stock exhaust. I've got a set of RevMarine pieces still to install. I think with anything aftermarket, we'll get a little more rumble.
Any thoughts on sealing the cut pieces?
#4
Registered
#5
Registered
Join Date: Oct 2005
Location: Lake of the Ozarks MO
Posts: 356
Likes: 0
Received 0 Likes
on
0 Posts
Hey Handfulz28,Years ago we would cut 4 inch deck drains in the bottom of the old style silent thunder boxes. In 1989 we sold 4 357`s w/575`s and speedmaster drives. Would you believe they came w/silent thunder!
We cut the drains in the so they would NOT be shot off the boat at speed!
These will help you with your problem, I think.
We cut the drains in the so they would NOT be shot off the boat at speed!
These will help you with your problem, I think.
#6
Registered
If You use a hole saw and tape it good it will be a pretty nice edge ... 4" seems big to me ... my drain holes are enlarged but not much ..... I have thought about adding a row along with the existing ones ....but want to run it first as is ...
what about adding exhaust trim rings ? Might look kewl to have tips too ...the angled cut with the long side toward the Transom ...short .. 1.5"
what about adding exhaust trim rings ? Might look kewl to have tips too ...the angled cut with the long side toward the Transom ...short .. 1.5"
Last edited by offthefront; 05-24-2007 at 08:50 PM.
#8
Registered
Thread Starter
Join Date: Aug 2006
Location: IAD/FLL
Posts: 2,090
Likes: 0
Received 0 Likes
on
0 Posts
Alright, so going with the holes is a done deal. I might shop the stores for deck drains to see what diameter they are and cut accordingly.
But still no yea/nea on whether to coat the newly exposed wood. Maybe a hefty coat of 5200 when I put the drains in?
But still no yea/nea on whether to coat the newly exposed wood. Maybe a hefty coat of 5200 when I put the drains in?
#9
Registered
Join Date: Aug 2002
Location: Eastern Lake Ontario
Posts: 2,896
Likes: 0
Received 3 Likes
on
3 Posts
I would go with the deck plate idea, then you can close them when you want. As for sealing anything, where you're going to cut the holes in the bottom of the ST box, there is no wood there, just fairly thick fiberglass. So, there is no real need to seal anything. Install the deck plates and seal them, you'll be all set.
#10
Registered
Thread Starter
Join Date: Aug 2006
Location: IAD/FLL
Posts: 2,090
Likes: 0
Received 0 Likes
on
0 Posts
I'll share pics as I go...