42 Poker Run rerig
#141
Registered
![](https://www.offshoreonly.com/forums/images/icons/platinum_member_star.gif)
Thread Starter
![Default](/forums/images/icons/icon1.gif)
![](https://cimg4.ibsrv.net/gimg/www.offshoreonly.com-vbulletin/1120x2000/img_20180323_141654177_e5754ad891c3300b3133bb65c9497baee359e408.jpg)
Everything is going to fit.
![](https://cimg1.ibsrv.net/gimg/www.offshoreonly.com-vbulletin/2000x1124/img_20180323_141312337_hdr_c77d9c66d4b8aea69ef4161f07fa08de4521ef7e.jpg)
#142
Registered
![](https://www.offshoreonly.com/forums/images/icons/platinum_member_star.gif)
Thread Starter
![Default](/forums/images/icons/icon1.gif)
Oil pans, drysump tanks, power steering tank, valve covers, and heads will all go to be anodized. When heads get back they will go to RFD to be cnced, seats and guides installed.
#143
Registered
![](https://www.offshoreonly.com/forums/images/icons/platinum_member_star.gif)
Thread Starter
![Default](/forums/images/icons/icon1.gif)
![](https://cimg7.ibsrv.net/gimg/www.offshoreonly.com-vbulletin/1400x2000/img_20180328_192735_4925b889105b1085ae49f4416105d3feab278de6.jpg)
Trailer at Myco getting rebunked.
#144
Registered
![](https://www.offshoreonly.com/forums/images/icons/platinum_member_star.gif)
Thread Starter
![Default](/forums/images/icons/icon1.gif)
![](https://cimg4.ibsrv.net/gimg/www.offshoreonly.com-vbulletin/1120x2000/img_20180328_182205990_760f54e9c557abbc5b97603ab47299c666b15ff2.jpg)
Lazer alignment tool, to get crank centerline on forward engine.
#146
Registered
![](https://www.offshoreonly.com/forums/images/icons/platinum_member_star.gif)
Thread Starter
![Default](/forums/images/icons/icon1.gif)
They made 750, before the upgrades. So we will have to wait and see. If I had to guess I would say right around 755.
#148
Registered
![](https://www.offshoreonly.com/forums/images/icons/platinum_member_star.gif)
Thread Starter
![Default](/forums/images/icons/icon1.gif)
We had brodix polish them they are being hard anodized blue, then off to RFD to be cnced. These have the offset runner in them so you have to run a offset in the rocker shafts.
#149
Registered
![](https://www.offshoreonly.com/forums/images/icons/platinum_member_star.gif)
Thread Starter
![Default](/forums/images/icons/icon1.gif)
Had to check the flow #s, intake is 490, exhaust is 340. They are 24B not 23B. My bad. Should be back mid week from being anodized. I'll post some pics when I get them.
#150
Registered
![](https://www.offshoreonly.com/forums/images/icons/platinum_member_star.gif)
Thread Starter
![Default](/forums/images/icons/icon1.gif)
![](https://cimg7.ibsrv.net/gimg/www.offshoreonly.com-vbulletin/2000x1124/img_20180329_144413870_top_143838e7fb77353e8207e247a85a0459d10f9c1d.jpg)
Been working on blueprinting bottom this week, should have it finished up next week.