Nothing ever goes right!!!!!! Transom assembly doesn't fit!!!
#11
Gone Fishin'
Charter Member
Thread Starter
Join Date: Nov 2000
Location: Grand Rapids/Holland/Grand Haven
Posts: 7,408
Likes: 0
Received 0 Likes
on
0 Posts
Borrowed an electric grinder and bit from Tinkerboater. Thanks a lot Steve!!!!!
I'll post when I've got it done and on the boat. Till then, don't call, don't email, don't PM, don't IM, etc.... I'M BUSY!!!!!!!!!!
I'll post when I've got it done and on the boat. Till then, don't call, don't email, don't PM, don't IM, etc.... I'M BUSY!!!!!!!!!!
__________________
[b]M Go Blue.......Gator boots, gator luggage, gator purses... all at cut rate deals!!!!
[b]M Go Blue.......Gator boots, gator luggage, gator purses... all at cut rate deals!!!!
#12
Official OSO boat whore
Charter Member
Join Date: Oct 2000
Location: Mequon, WI
Posts: 6,157
Likes: 0
Received 0 Likes
on
0 Posts
If you are really using a grinding wheel, you'll need a special one for aluminum. The regular steel wheels will quickly load up. Of course you're not doing much so it might not matter...
#14
Registered
Join Date: Nov 2000
Location: Sevierville,TN
Posts: 131
Likes: 0
Received 0 Likes
on
0 Posts
I would double check before I started drilling. I would guess the fitting on the drive will work like a one way valve letting water in when the drive cools off.
You may be better off taking out the valve and plugging the hole.
You may be better off taking out the valve and plugging the hole.
#15
Gone Fishin'
Charter Member
Thread Starter
Join Date: Nov 2000
Location: Grand Rapids/Holland/Grand Haven
Posts: 7,408
Likes: 0
Received 0 Likes
on
0 Posts
RickR, I'm grinding on the INNER plate, not the outer. So, no water issues or leaks of any kind. I understand the one way valve on the drive/bell housing. No sweat!! But thanks for the concern.
__________________
[b]M Go Blue.......Gator boots, gator luggage, gator purses... all at cut rate deals!!!!
[b]M Go Blue.......Gator boots, gator luggage, gator purses... all at cut rate deals!!!!
#16
Like formula 31 said just spray WD-40 on what you are grinding (about every 10 seconds of grinding) and it won't load up as fast with aluminum. Hell MIKE if you had told me you just needed a hole I have bits all the way up to 6 inches. And the drill to turn it.
3/4 inch hole in 1/2 inch aluminum takes about 1 minute.
3/4 inch hole in 1/2 inch aluminum takes about 1 minute.
#17
Gone Fishin'
Charter Member
Thread Starter
Join Date: Nov 2000
Location: Grand Rapids/Holland/Grand Haven
Posts: 7,408
Likes: 0
Received 0 Likes
on
0 Posts
Steve, I'm done grinding. Need help putting it on the boat.
__________________
[b]M Go Blue.......Gator boots, gator luggage, gator purses... all at cut rate deals!!!!
[b]M Go Blue.......Gator boots, gator luggage, gator purses... all at cut rate deals!!!!
#19
Gone Fishin'
Charter Member
Thread Starter
Join Date: Nov 2000
Location: Grand Rapids/Holland/Grand Haven
Posts: 7,408
Likes: 0
Received 0 Likes
on
0 Posts
Thanks Steve. I should be home around 4:00 or so.
__________________
[b]M Go Blue.......Gator boots, gator luggage, gator purses... all at cut rate deals!!!!
[b]M Go Blue.......Gator boots, gator luggage, gator purses... all at cut rate deals!!!!
#20
Charter Member #232
Charter Member
Cool deal Foul get your azz back out on the water!!! Hey you have the alignment tool right!!!
__________________
Put your best foot forward!
Put your best foot forward!