Noisy outdrive
#11
Registered
![Default](/forums/images/icons/icon1.gif)
Originally Posted by alorio1
Well the local boat mechanic said it would take a week just to get to the tearing into the outdrive and the cost would be $450 to 500 bucks to replace Gimbel brg.
So, I went to the local marine parts store and purchased the bearing, gasket set, a MERCRUISER STERN DRIVE SHOP MANUAL and a tube of aqua-lube grease , which they recomended to use for the u-joints.
On the way home I stopped by my local Auto Zone and rented a Three prong hammer knocker bearing puller, which they refund all your money when you return their tools, studied the Mercruiser manual for about thirty minutes then tore into the outdrive.
You guys were right on the money with the Gimbel brg. being the culprit.......Installed the new brg.(aligned the grease passage hole to match hole in brg housing grease port)inspected both u-joints no problem here, so they got the lube job they needed and back in with the outdrive.
Total time spent with the actual repair was about three hours.......total cost for parts and repair manual was about $100 bucks.
All suggestions came in handy such as putting the shift in forward before removing outdrive aligning lever ect.ect.
Some say it doesn't matter if the gimble brg. grease port is not matched up with the brg. housing port but I am a firm believer that is not the right way to install the brg.......The old brg. I removed was dry from lack of grease and the grease port holes were not matched.There was a lot of grease on the engine side of the brg. as if when it was greased the grease found another route to take other than the intended brg. internals.
Checked boat out today......no more noisy outdrive problems.
Thanks to all for suggestions and replies, not to mention the experience I gained and the savings ............Joe
So, I went to the local marine parts store and purchased the bearing, gasket set, a MERCRUISER STERN DRIVE SHOP MANUAL and a tube of aqua-lube grease , which they recomended to use for the u-joints.
On the way home I stopped by my local Auto Zone and rented a Three prong hammer knocker bearing puller, which they refund all your money when you return their tools, studied the Mercruiser manual for about thirty minutes then tore into the outdrive.
You guys were right on the money with the Gimbel brg. being the culprit.......Installed the new brg.(aligned the grease passage hole to match hole in brg housing grease port)inspected both u-joints no problem here, so they got the lube job they needed and back in with the outdrive.
Total time spent with the actual repair was about three hours.......total cost for parts and repair manual was about $100 bucks.
All suggestions came in handy such as putting the shift in forward before removing outdrive aligning lever ect.ect.
Some say it doesn't matter if the gimble brg. grease port is not matched up with the brg. housing port but I am a firm believer that is not the right way to install the brg.......The old brg. I removed was dry from lack of grease and the grease port holes were not matched.There was a lot of grease on the engine side of the brg. as if when it was greased the grease found another route to take other than the intended brg. internals.
Checked boat out today......no more noisy outdrive problems.
Thanks to all for suggestions and replies, not to mention the experience I gained and the savings ............Joe
Last edited by outdrive man; 07-31-2005 at 10:07 PM.
#12
Registered
![Default](/forums/images/icons/icon1.gif)
Originally Posted by outdrive man
400-500, thats highway f-ck`n robbery. i do this for a living we charge 75 for the drive service with gaer lube and 75 to chang gimbal bearing. trust me were not hurting
He was very happy with the work & the "care" you took of his boat.....Good for you !
#13
Registered
![Default](/forums/images/icons/icon1.gif)
Originally Posted by birdog
Your shop just replaced a coupler on a very good friends boat.
He was very happy with the work & the "care" you took of his boat.....Good for you !
He was very happy with the work & the "care" you took of his boat.....Good for you !
#14
Registered
Join Date: Apr 2005
Location: KENT ISLAND, MARYLAND
Posts: 2,675
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
OUTDRIVE MAN ,
like your thinking!!! we are the maryland east coast cig,foutain,active,sonic dealer and yes it is that little extra that makes the differance....my thinking is I will treat your boat as mine......
problem....
my customers keep getting faster then mine so i have to keep spending money on mine!!!!
like your thinking!!! we are the maryland east coast cig,foutain,active,sonic dealer and yes it is that little extra that makes the differance....my thinking is I will treat your boat as mine......
problem....
my customers keep getting faster then mine so i have to keep spending money on mine!!!!
#15
Registered
Join Date: Oct 2004
Location: medellin colombia, pablo escobar's lil town
Posts: 8,390
Likes: 0
Received 6 Likes
on
4 Posts
![Default](/forums/images/icons/icon1.gif)
400-500, thats highway f-ck`n robbery.