454 Mag MPI fuel problem
#11
Registered
Join Date: May 2005
Location: LOTO Performance Boat Center
Posts: 3,897
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
Had my motor checked on the merc scan tool and no codes came up, none where stored in the memory. Talked to the mechanic who ran the test and he recommended replacing the IAC motor, a couple of the other techs recommended the same as well. I bought a new one for $80 buck and installed it, the boat fired up on the hose fine and started with authority numerous times. The marina bid not even charge me for the test, I guess that is a fringe benefit for being a former employee. I guess time will tell if this is the permanent fix, but the engine sounded alot healthier at idle and start up.
![Big Grin](/forums/images/smilies/biggrin.gif)
#12
Registered
Join Date: Nov 2003
Location: Melbourne, FL
Posts: 1,243
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
I had similar problem and it ended up being the fuel pressure regulator. I did replace the IAC and got it from automotive supply house for a lot less than the "marine" version. Exact same GM part numbers.
My pressure regulator and rusted and was binding the diagphram. THe rust ( and the GM part number) were covered by the pain the manufacturer had applied. It had almost rusted thru when it started causing problems and we tested everything and changed the IAC before we discovered the rust bubles in paint.
My pressure regulator and rusted and was binding the diagphram. THe rust ( and the GM part number) were covered by the pain the manufacturer had applied. It had almost rusted thru when it started causing problems and we tested everything and changed the IAC before we discovered the rust bubles in paint.
#14
Registered
Join Date: May 2005
Location: LOTO Performance Boat Center
Posts: 3,897
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
Well it did it again. Althougth this time it did not even want to idle and suck air, it just plain wouldn't fire over. I let the boat sit for an hour and it fired up just fine. I am begining to think that it is vapor lock. Where is the fuel rail shrader valve??
What is the VST? Where is it on the motor? The motor is a 1999.
What is the VST? Where is it on the motor? The motor is a 1999.
#15
Gold Member
![](https://www.offshoreonly.com/forums/images/icons/gold_member_star.gif)
![Talking](/forums/images/icons/icon10.gif)
well, sorry to hear that you still have the problem. The shrader valve should be in the front of the intake area just under the center of the plenum. Right around the t-stat housing. If your motor has a VST tank, this will be located on the odd bank side at the rear. (port) It will have 2 hose going to it and 2 wires. It will be on top just next to the distributer.
Good luck, keep us informed.
John
Good luck, keep us informed.
John
![Big Grin](/forums/images/smilies/biggrin.gif)
#16
Registered
Join Date: Apr 2005
Location: KENT ISLAND, MARYLAND
Posts: 2,675
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
The vst is a vapor separator tank it acts kind of like a fuel bowl in a carburetor in the chamber is a fuel pump, float, needle valve the idea is to bleed out any air in the fuel line so the motor doesn't vapor lock and has a contsant suppy of fuel.
Last edited by GOODT; 08-07-2005 at 01:18 PM.
#18
Registered
![Default](/forums/images/icons/icon1.gif)
There is some good information about vapor lock in Mercruiser Service Bulletin 99-7. A pdf file of this bulletin is available at another site. Not sure if its ok to post link here.
Dave
Dave
#20
Registered
![Default](/forums/images/icons/icon1.gif)