What size of socket for an Eagle H Beam Rod?
03-06-2006, 09:35 AM
#1
Registered
Thread Starter
What size of socket for an Eagle H Beam Rod?
Guys I am at work and was going to purchase a new socket at lunch and I can not remember what size of cap screw is on the rod.
12 point 3/8?
Thanks
JIM
12 point 3/8?
Thanks
JIM
03-06-2006, 10:36 AM
#2
Registered
Join Date: Dec 2000
Location: Paducah, KY
Posts: 194
Likes: 0
Received 0 Likes
on
0 Posts
Re: What size of socket for an Eagle H Beam Rod?
I believe you are correct on the size if you are using ARP 2000 series bolts. I would purchase one of good quality. Mine got quite of a workout during assembly. If you plan on plastigauging to check your clearances you could be torquing, re-torquing and possibly changing to undersize/oversize bearings which means even more torquing.
03-06-2006, 10:50 AM
#4
Registered
Join Date: Jan 2004
Location: San Diego, California
Posts: 2,777
Likes: 0
Received 6 Likes
on
6 Posts
Re: What size of socket for an Eagle H Beam Rod?
Don't forget to tighten the rod bolts up to the torque spec at leat 4-5 times to properly set the threads and pre-stretch on the bolts. This is the one problem most aftermarket rods can have after assembly, improper set up for final torque coupled with not properly checking bearing clearances and pin fit in the rods. If your going to spend dollars for good rods make sure you do the "right" job on checking and assembly! The socket size is the easiest but not the most important.
Ray @ Raylar
Ray @ Raylar
03-06-2006, 12:33 PM
#5
Registered
Thread Starter
Re: What size of socket for an Eagle H Beam Rod?
So I will by a 1/2 and 3/8 12 point.
Actually the engine is assembled I was taking off some caps to make sure the bearings look fine. The mains are perfect. I found some shiny particals in my oil filter at the end of last season. I am hoping they were from the previoius spun bearing
No signs of metal in the pan or any where else so I am keeping my fingers crossed
Actually the engine is assembled I was taking off some caps to make sure the bearings look fine. The mains are perfect. I found some shiny particals in my oil filter at the end of last season. I am hoping they were from the previoius spun bearing
No signs of metal in the pan or any where else so I am keeping my fingers crossed
03-06-2006, 04:47 PM
#8
Registered
Join Date: Oct 2004
Location: medellin colombia, pablo escobar's lil town
Posts: 8,390
Likes: 0
Received 6 Likes
on
4 Posts
Re: What size of socket for an Eagle H Beam Rod?
measure rod bolt stretch the measuring gauges are about 60bucks but well worth it for the peace of mind, good luck
03-07-2006, 06:50 AM
#9
Registered
Thread Starter
Re: What size of socket for an Eagle H Beam Rod?
7/16 is the winner!
How can I measure rod bolt stretch when its a cap screw/bolt?
How can I measure rod bolt stretch when its a cap screw/bolt?
03-07-2006, 07:00 AM
#10
Re: What size of socket for an Eagle H Beam Rod?
Mine are threaded through and not blind. If your are open, you need the special indicator. It has extensions to go into the end of the threaded hole to get to the end of the bolt. The measurement is then from the head to the end of the bolt. Mics wont work. The end of the bolt and the head has a center cut on it to position the indicator shafts.
