Braided Hose HELP Needed
#12
Registered
Join Date: Jul 2005
Location: Seattle, WA
Posts: 4
Likes: 0
Received 0 Likes
on
0 Posts
#13
Platinum Member
Platinum Member
Join Date: Nov 2002
Location: LONG ISLAND/LAKE MURRAY
Posts: 2,399
Likes: 0
Received 1 Like
on
1 Post
Re: Braided Hose HELP Needed
I usually take the end of the hose & bevel it on a bench grinder. A little oil and screw the red fitting a few turns but not all the way so you can start threading the blue end in. If the red fitting is bottomed out into the hose you'll never get the blue fitting in.
#14
Registered
Join Date: Sep 2004
Location: Torrance, California
Posts: 362
Likes: 0
Received 0 Likes
on
0 Posts
Re: Braided Hose HELP Needed
I think I would rather go to the Dentist then deal with braided line. There is no other pain like stainless steel wire stabbing u.
#16
Registered
Join Date: Feb 2001
Location: LANCASTER, NEW YORK 14086
Posts: 422
Likes: 0
Received 4 Likes
on
2 Posts
Re: Braided Hose HELP Needed
Maybe your's are different but the ones I use the red part threads on the braided hose ? I can't remember if it's standard or reverse thread but it definately threads on.
#17
Registered
Thread Starter
Re: Braided Hose HELP Needed
Great to say mission accomplished. After you do your first one and get it fiqured out it easy. If I where going to do several hoes I would buy the tool.
I even put them together with a cast on my hand using only my thumb and one finger Now that was tricky!
I even put them together with a cast on my hand using only my thumb and one finger Now that was tricky!
#18
Registered
Join Date: Feb 2005
Location: long island, newyork
Posts: 2,551
Likes: 0
Received 2 Likes
on
2 Posts
Re: Braided Hose HELP Needed
DO NOT LEAVE THE TAPE ON. to cut to length your hose use a shear. no grinding , no oil nada. start by cocking the female end on the hose . use a lil downward pressure then rotate. works every time. use a suitable lubricant, i chose never seize as to reduce galling of the aluminium to aluminium contact. and make sure you rinse the lines thoroughly.
heres a couple of hoses i had to make in sizes rangeing from -4 to -20.
good luck
heres a couple of hoses i had to make in sizes rangeing from -4 to -20.
good luck
#20
Banned
Join Date: Sep 2001
Location: Deland, Florida
Posts: 25,191
Likes: 0
Received 0 Likes
on
0 Posts
Re: Braided Hose HELP Needed
If you look at my other thread, I have been totally unable to bend steel lines.
The thing is, I had a braided line on the same size engine sitting in my garage. I told Deb to take it off and hand it to me, figuring I had it made. Hell no! I didn't think about the new engine having closed cooling, so now my line isn't long enough. I'd order one from somebody if I knew what size this stuff is. When I had this one made, I just went to a speed shop in Clearwater, and told them what I needed, and they made it up for me. Can anyone tell from the pictures what size fitting they are? They are on a sbc.
The thing is, I had a braided line on the same size engine sitting in my garage. I told Deb to take it off and hand it to me, figuring I had it made. Hell no! I didn't think about the new engine having closed cooling, so now my line isn't long enough. I'd order one from somebody if I knew what size this stuff is. When I had this one made, I just went to a speed shop in Clearwater, and told them what I needed, and they made it up for me. Can anyone tell from the pictures what size fitting they are? They are on a sbc.