Adjusting lifters 1/2 3/4 maybe more?
#1
Registered
Thread Starter
![Default](/forums/images/icons/icon1.gif)
Crane lifters and rocker arms. Got a few noisy ones. Ran the boat an hour to see if they would quite down some. Only have a few that are making a tick a various RPM between idle and 1500. You can sort of hear it if you use a hose held to the ear and rocker tip. I set them back to 0 and then 3/4 turn. Still made noise so I went an 1/8 more on these. Still a little clicking sound. Not bad but the others are silent.
How many turns is the max for tightening down? Might go the max to see if they quite down, if not just back them off to 3/4 and go with it.
Tim T.
How many turns is the max for tightening down? Might go the max to see if they quite down, if not just back them off to 3/4 and go with it.
Tim T.
#2
Registered
Join Date: Aug 2005
Location: Colchester Vermont
Posts: 520
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
Originally Posted by BadDog
Crane lifters and rocker arms. Got a few noisy ones. Ran the boat an hour to see if they would quite down some. Only have a few that are making a tick a various RPM between idle and 1500. You can sort of hear it if you use a hose held to the ear and rocker tip. I set them back to 0 and then 3/4 turn. Still made noise so I went an 1/8 more on these. Still a little clicking sound. Not bad but the others are silent.
How many turns is the max for tightening down? Might go the max to see if they quite down, if not just back them off to 3/4 and go with it.
Tim T.
How many turns is the max for tightening down? Might go the max to see if they quite down, if not just back them off to 3/4 and go with it.
Tim T.
Might want too start over and make sure valves are all the way closed before adjusting.
#4
SORE MEMBER
![](https://www.offshoreonly.com/forums/images/icons/platinum_member_star.gif)
Join Date: Apr 2004
Location: 29°50'49.74"N 95° 5'17.55"W.......TEXAS
Posts: 6,989
Likes: 0
Received 1 Like
on
1 Post
![Default](/forums/images/icons/icon1.gif)
Are these new heads / valves /guides.
My buddy kept chasing a noisy lifter, turned out it was a badly worn valve guide, valve was getting cocked on seat (noise) eventually it broke and destroyed the motor.
I would think 1/2 turn after zero lash would be fine for hydraulic lifters. If they are solid then you need to set the old fashioned way
My buddy kept chasing a noisy lifter, turned out it was a badly worn valve guide, valve was getting cocked on seat (noise) eventually it broke and destroyed the motor.
I would think 1/2 turn after zero lash would be fine for hydraulic lifters. If they are solid then you need to set the old fashioned way
![Big Grin](/forums/images/smilies/biggrin.gif)
#6
Registered
Thread Starter
![Default](/forums/images/icons/icon1.gif)
Fresh heads and rockers, lifters have maybe 50 hours on them. Fresh motor, forge pistons, new rods etc.
#7
Registered
![Default](/forums/images/icons/icon1.gif)
Flat tappet or Hydraulic roller or something else ?
Roller rockers or stamped steel ?
Roller rockers or stamped steel ?
#9
Registered
![Default](/forums/images/icons/icon1.gif)
Just so you know - aggresive ramped HR cams (such as most of Crane's ) along with roller rockers can emit ticking noises that are audubile to the ear even without a hose / stethascope. Very, very normal.
#10
SORE MEMBER
![](https://www.offshoreonly.com/forums/images/icons/platinum_member_star.gif)
Join Date: Apr 2004
Location: 29°50'49.74"N 95° 5'17.55"W.......TEXAS
Posts: 6,989
Likes: 0
Received 1 Like
on
1 Post
![Default](/forums/images/icons/icon1.gif)
Originally Posted by SB
Just so you know - aggresive ramped HR cams (such as most of Crane's ) along with roller rockers can emit ticking noises that are audubile to the ear even without a hose / stethascope. Very, very normal.
It can get messy, but if you are able to run motor without valve cover on, you can take a balled up rag and cover each lifter in turn to see if it's just one or all of them taking turns.