Water Crossover with or without bypass??
#1
Registered
Thread Starter
Join Date: Mar 2001
Location: Southwestern OH, USA
Posts: 130
Likes: 0
Received 0 Likes
on
0 Posts
Water Crossover with or without bypass??
What application do you want the bypass on the crossover?? I was looking on Tricks site that they sell both kind of kits.
#2
Platinum Member
Platinum Member
I was just asking the same kinds of questions not too long ago.
The deciding factor is whether you use a T-stat or not.
If there's no T-stat, water will always flow through the block, out the empty T-stat housing and out to the exhaust at all times, without over-pressurizing.
However you run the risk of running too cold this way, and with and EFI engine, that's no good. Usually only big blower motors run like this, because they're making too much heat in most instances.
If you use use a T-stat to control temps, you should have a by-pass so that water can still flow into the exhaust while the engine's still too cold to open up the T-stat, and also relieve some block pressure.
If you do go the T-stat route, it's also a good idea to drill 2 or three 1/8" to 3/16" holes around the perimeter of the t-stat so that even when it's cold some water will move through the block at all times. You don't want non-moving water just sitting in your block.
How many holes and what size is pretty much trial and error monitoring your temps.
Here's a recent thread with another good link within.
http://www.offshoreonly.com/forums/s...d.php?t=165707
The deciding factor is whether you use a T-stat or not.
If there's no T-stat, water will always flow through the block, out the empty T-stat housing and out to the exhaust at all times, without over-pressurizing.
However you run the risk of running too cold this way, and with and EFI engine, that's no good. Usually only big blower motors run like this, because they're making too much heat in most instances.
If you use use a T-stat to control temps, you should have a by-pass so that water can still flow into the exhaust while the engine's still too cold to open up the T-stat, and also relieve some block pressure.
If you do go the T-stat route, it's also a good idea to drill 2 or three 1/8" to 3/16" holes around the perimeter of the t-stat so that even when it's cold some water will move through the block at all times. You don't want non-moving water just sitting in your block.
How many holes and what size is pretty much trial and error monitoring your temps.
Here's a recent thread with another good link within.
http://www.offshoreonly.com/forums/s...d.php?t=165707
Last edited by CigDaze; 09-21-2007 at 03:47 PM.
The following users liked this post:
Lancer19 (05-10-2024)
#3
Geronimo36
Gold Member
My opinion is that it depends how much power you're making....
I've run it both ways over the years.... 500-550 NA's with bypass and t-stat and 830 hp supercharged without t-stat and bypass.
If you're not running big power I would run a t-stat but thats just my opinion.
I've run it both ways over the years.... 500-550 NA's with bypass and t-stat and 830 hp supercharged without t-stat and bypass.
If you're not running big power I would run a t-stat but thats just my opinion.
#4
Registered
Join Date: Aug 2006
Location: Colonial Beach VA
Posts: 629
Likes: 0
Received 0 Likes
on
0 Posts
Just a little side rant about the kits with cross-over and thermo housing
why dont they come with belts?
the belts have to be different , your eliminating the water pump !?!?!?
why dont they come with belts?
the belts have to be different , your eliminating the water pump !?!?!?
#5
Geronimo36
Gold Member
The raw water pump belt stays the same.
#6
Registered
Join Date: Aug 2006
Location: Colonial Beach VA
Posts: 629
Likes: 0
Received 0 Likes
on
0 Posts
i know my sea water pump is a belt on its own , but the alternator and PS pump both run around the water pump , they keep it spinning , and i dont see e-nuff adjstment in there brackets to compensate for loss of water pump in the mix
#7
Registered
Join Date: Dec 2005
Location: Mission Viejo, CA
Posts: 390
Likes: 0
Received 0 Likes
on
0 Posts
900++ Hp w/ blower and no circulating pump. I always run a thermostat because I want my engines and oil to warm up efficiently before going "BIG". I would only run without one if there was absolutely no other way....
Last edited by ghittner; 09-26-2007 at 12:35 AM.
#8
VIP Member
VIP Member
And my power steering and alternator run off of what ?
i know my sea water pump is a belt on its own , but the alternator and PS pump both run around the water pump , they keep it spinning , and i dont see e-nuff adjstment in there brackets to compensate for loss of water pump in the mix
i know my sea water pump is a belt on its own , but the alternator and PS pump both run around the water pump , they keep it spinning , and i dont see e-nuff adjstment in there brackets to compensate for loss of water pump in the mix
Ummmm, maybe they use the pully on the front of the crankshaft??????????? Just a guess!
I run a crossover with no thermostat. Big cube N/A's.
__________________
Happily retired and living in Heavens waiting room.
Happily retired and living in Heavens waiting room.
#9
Geronimo36
Gold Member
And my power steering and alternator run off of what ?
i know my sea water pump is a belt on its own , but the alternator and PS pump both run around the water pump , they keep it spinning , and i dont see e-nuff adjstment in there brackets to compensate for loss of water pump in the mix
i know my sea water pump is a belt on its own , but the alternator and PS pump both run around the water pump , they keep it spinning , and i dont see e-nuff adjstment in there brackets to compensate for loss of water pump in the mix
Last edited by Panther; 09-26-2007 at 08:19 AM.
#10
Registered
Join Date: Dec 2005
Location: Mission Viejo, CA
Posts: 390
Likes: 0
Received 0 Likes
on
0 Posts