ZZ502 w 741 cam issues
#11
Registered
Thread Starter
![Default](/forums/images/icons/icon1.gif)
1BIGJIM, I just noticed you have a Pachanga, is yours a 22 or 27?
If 22, if you had RMBuilder make you a cam that is larger I am going to assume you have more power than I do. ( Actives Dyno was 560 something ).
What is your setup?
I am going to work the bottom of mine, add a 2" shorty and get BBlades on the prop ( he does my drag stuff )
Looking for mid 80's
RT
If 22, if you had RMBuilder make you a cam that is larger I am going to assume you have more power than I do. ( Actives Dyno was 560 something ).
What is your setup?
I am going to work the bottom of mine, add a 2" shorty and get BBlades on the prop ( he does my drag stuff )
Looking for mid 80's
RT
#13
Registered
Thread Starter
![Default](/forums/images/icons/icon1.gif)
Yes, that was one thing I did check.
But it does make sense that the cooling, specially with the aluminium heads needs to be changed.
RT
But it does make sense that the cooling, specially with the aluminium heads needs to be changed.
RT
Last edited by RBT; 11-21-2007 at 08:12 AM.
#14
Geronimo36
![](https://www.offshoreonly.com/forums/images/icons/gold_member_star.gif)
![Default](/forums/images/icons/icon1.gif)
Are you running a power valve in the carb? If not, you may want to jet down in the primaries and install a 6.5 PV. If you're running a PV, which one is in there? You may have the wrong PV or it could even been blown and with that cam it's activating the powervalve at idle causing you to foul plugs.
When the engine is at idle take off the flame arrestor and look down into the venturi of the primary. If you see fuel slowly dripping down from the venturi you know you found the problem.
When the engine is at idle take off the flame arrestor and look down into the venturi of the primary. If you see fuel slowly dripping down from the venturi you know you found the problem.
#15
Registered
Join Date: Aug 2001
Location: lake of the ozarks,missouri
Posts: 214
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
if you really do have 4.5 vacumn at idle in gear and you are idling in gear at 750 rpm or above, then i would recommend a 2.5 power valve and jet accordingly
#16
Geronimo36
![](https://www.offshoreonly.com/forums/images/icons/gold_member_star.gif)
![Default](/forums/images/icons/icon1.gif)
Please don't rip off the cylinder heads and tear into the engine before looking at the carb..... A lot of which has been posted could be possible but I really doubt it.
Also, what plugs are you running?
I think it's your tune... Just my .02.
Also, what plugs are you running?
I think it's your tune... Just my .02.
#17
Registered
Thread Starter
![Default](/forums/images/icons/icon1.gif)
Oh I know it is my tune, and the external parts. The motor has perfect leakdown. Mechanically it is perfect.
I am so used to EFI ( I program Merc box's, Race, Optimax and Verado ) and I am too damn young to care about carbs.
RT
I am so used to EFI ( I program Merc box's, Race, Optimax and Verado ) and I am too damn young to care about carbs.
RT
#18
Geronimo36
![](https://www.offshoreonly.com/forums/images/icons/gold_member_star.gif)
![Default](/forums/images/icons/icon1.gif)
EFI get thrown off by temperature flutuations (open loop/closed)...not so much on carbs...
I run 100* water temps all day long with a huffer on top, two carbs, 580 cubes, decent size cam, 30 minute idle out to the ocean etc....and not once have I ever fouled a plug.
It's the setup, whether it be carbs, timing or wrong heat range on the plugs IMHO.
I run 100* water temps all day long with a huffer on top, two carbs, 580 cubes, decent size cam, 30 minute idle out to the ocean etc....and not once have I ever fouled a plug.
It's the setup, whether it be carbs, timing or wrong heat range on the plugs IMHO.
Last edited by Panther; 11-21-2007 at 09:21 AM.
#20
Registered
Thread Starter
![Default](/forums/images/icons/icon1.gif)
EFI get thrown off by temperature flutuations (open loop/closed)...not so much on carbs...
I run 100* water temps all day long with a huffer on top, two carbs, 580 cubes, decent size cam, 30 minute idle out to the ocean etc....and not once have I ever fouled a plug.
It's the setup, whether it be carbs, timing or wrong heat range on the plugs IMHO.
I run 100* water temps all day long with a huffer on top, two carbs, 580 cubes, decent size cam, 30 minute idle out to the ocean etc....and not once have I ever fouled a plug.
It's the setup, whether it be carbs, timing or wrong heat range on the plugs IMHO.
See, I can make a 430hp drag outboard idle at 700 rpm all day, shift gears without stalling and turn 11 100 rpm pass after pass. The only part I cannot compensate electronically is humidity, and that is becasue we cannot run O2 or Lambada due to the oil.
TUNE IS EVERYTHING, I can read plugs..... I just need to know where to go to make them read right!
I figured the cooling, and know that carb is off...... but where and you guys are giving me some ideas!
Thanks