How to prevent oil from pushing through breathers?
#1
I hate the winter!!
![](https://www.offshoreonly.com/forums/images/icons/platinum_member_star.gif)
Thread Starter
Join Date: Jul 2001
Location: long island, new york
Posts: 2,707
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
I have been having a minor problem with oil pushing past the breathers. The engine is fresh, leakdown is good. Normal amount of blow by, nothing to even consider. The problem only occurs after long full throttle or near full throttle runs. Even then, it isnt much. It just squirts out a bit of oil on both valve covers. Its just that I am such an anal SOB, it bothers the crap out of me. I have looked into hooking up a recovery system, but cant find anything I like. What are you guys doing?
#3
Pirate of the Chesapeake
![](https://www.offshoreonly.com/forums/images/icons/gold_member_star.gif)
Join Date: Aug 2006
Location: North Point Creek, Md.
Posts: 4,330
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
Run puke tanks on the motors if it bothers you.I got two for sale ,was going to put them on my blower motors but had no room. JOHN
#4
I hate the winter!!
![](https://www.offshoreonly.com/forums/images/icons/platinum_member_star.gif)
Thread Starter
Join Date: Jul 2001
Location: long island, new york
Posts: 2,707
Likes: 0
Received 0 Likes
on
0 Posts
#5
I hate the winter!!
![](https://www.offshoreonly.com/forums/images/icons/platinum_member_star.gif)
Thread Starter
Join Date: Jul 2001
Location: long island, new york
Posts: 2,707
Likes: 0
Received 0 Likes
on
0 Posts
#7
I hate the winter!!
![](https://www.offshoreonly.com/forums/images/icons/platinum_member_star.gif)
Thread Starter
Join Date: Jul 2001
Location: long island, new york
Posts: 2,707
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
Thanks, that is what I was thinking of. The only problem is I cant find anything to screw into the covers, except for what I have. Anyone done something similiar with 2 piece Eckerts like I have?
#8
Gold Member
![](https://www.offshoreonly.com/forums/images/icons/gold_member_star.gif)
Join Date: Mar 2003
Location: Grosse ile michigan
Posts: 2,374
Likes: 0
Received 91 Likes
on
36 Posts
![Default](/forums/images/icons/icon1.gif)
Are the breather holes threaded in your valve covers if so you can use aeroquipp fittings to get to what ya need i will find a pick for ya.........If they are not ya have to weld a threaded fitting from the back side......
#9
Gold Member
![](https://www.offshoreonly.com/forums/images/icons/gold_member_star.gif)
Join Date: Mar 2003
Location: Grosse ile michigan
Posts: 2,374
Likes: 0
Received 91 Likes
on
36 Posts
![Default](/forums/images/icons/icon1.gif)
I was lucky mine were already aluminum, so i just welded some #12 90's into my threaded bungs hope this helps......I think imco makes something also, check there web site....
#10
Charter Member #601
![](https://www.offshoreonly.com/forums/images/icons/charter_member_star.gif)
![Default](/forums/images/icons/icon1.gif)
Vinny, let me know what you come up with. I will have to do something with mine also.
I have regular Chevy Aluminum covers.. push in with grommets.
Dick
I have regular Chevy Aluminum covers.. push in with grommets.
Dick