Distributor-Rebuild or Replace?
#11
Charter Member #818
![](https://www.offshoreonly.com/forums/images/icons/charter_member_star.gif)
Thread Starter
Join Date: Jan 2001
Location: West Michigan & Higgins Lake
Posts: 644
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
BGIII, The guy that fixed my distributor works out of his house. He is the first house west of Homrich on 76th street , near Byron Center. I don't have his phone number handy. I'll try to find it and post it tomorrow. Otherwise you could just go to his place. He is usually there working in the garage next to the house. Doug
#12
Charter Member # 1083
![](https://www.offshoreonly.com/forums/images/icons/charter_member_star.gif)
Join Date: Feb 2001
Location: BACK HOME AGAIN IN INDIANA
Posts: 159
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
Sorry I got to this so late but, The bushings (2) are part number: 23-90915. They are 3.65. You can get them at any Merc. Dealer.
They will probably need to order them for you.
Did mine last year 486 hrs on that motor. The other one was fine.
You should check your intake manifold to make sure the allignment is right.
Bob
They will probably need to order them for you.
Did mine last year 486 hrs on that motor. The other one was fine.
You should check your intake manifold to make sure the allignment is right.
Bob
__________________
If it's not a thunder run.............than you're just burnen fuel!!!
If it's not a thunder run.............than you're just burnen fuel!!!
#14
Charter Member #818
![](https://www.offshoreonly.com/forums/images/icons/charter_member_star.gif)
Thread Starter
Join Date: Jan 2001
Location: West Michigan & Higgins Lake
Posts: 644
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
I did find his number, finally. It is 616-878-9734. He is on the north side of 76th at 3691. Best time to call is probably 9 to 5. Good luck, Doug
#16
Charter Member #818
![](https://www.offshoreonly.com/forums/images/icons/charter_member_star.gif)
Thread Starter
Join Date: Jan 2001
Location: West Michigan & Higgins Lake
Posts: 644
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
That's great, BGIII.
He must have still had the extra bushing that he ordered for mine. He said he ordered two but, only used one of them. Glad you found him OK. Sorry I wasn't able to get the number to you in time to call him. Look forward to meeting you soon! Are you going to Grand Haven this Saturday to watch the poker run? I am going to be there about 9am and go out in the lake so I can watch them take off from the water. It was awesome last year.
See ya, Doug
He must have still had the extra bushing that he ordered for mine. He said he ordered two but, only used one of them. Glad you found him OK. Sorry I wasn't able to get the number to you in time to call him. Look forward to meeting you soon! Are you going to Grand Haven this Saturday to watch the poker run? I am going to be there about 9am and go out in the lake so I can watch them take off from the water. It was awesome last year.
See ya, Doug
#17
Registered
![Default](/forums/images/icons/icon1.gif)
Hope to be out there Friday night & Saturday morning. Boss lives in Grand Haven on the channel so I have a good vantage point for activity in the channel. Boat is not ready yet but soon. Hope to go on one of the fun runs this summer.
Thread
Thread Starter
Forum
Replies
Last Post
stevel
General Boating Discussion
6
04-03-2002 05:33 PM