Testing an ECT sensor
#1
Ginger or Mary Ann?
Charter Member
Thread Starter
Testing an ECT sensor
This sensor, (Engine Coolant Temp) is sending a varible voltage of up to 5V to the ECM to adjust fuel mixture. Can this sender be bypassed by jumping across the 2 wires in the sensor plug, or unplugging the wires, or can't be bypassed, only tested? I'm thinking it will either send a full 5 volts thru, or zero volts. Not sure what voltage the ECM is looking for when cold.
Motor just cranks, no start when cold. After several minutes, it will finally catch, then all is well. A marine mechanic has suggested to check this sensor.
Thanks
Motor just cranks, no start when cold. After several minutes, it will finally catch, then all is well. A marine mechanic has suggested to check this sensor.
Thanks
__________________
Some people are like Slinkies - Not really good for anything, but they
bring a smile to your face when pushed down the stairs.
Some people are like Slinkies - Not really good for anything, but they
bring a smile to your face when pushed down the stairs.
Last edited by US1 Fountain; 05-16-2011 at 08:42 PM.
#2
coolrunning racing
VIP Member
ECT sender is "engine coolant temperature". Typical two wire that uses reference voltage if you unplug it the ECU would not receive any voltage. If you jump the terminals the ECU would receive full reference voltage. With regards to the ECT sensor cold stat would be affected if the ECU thinks it is hot, as well hot restarts would be affected with an over rich condition if it thinks it is cold. You can ohm out the sensor cold and then again hot and it would tell you if it is in working condition but using a scan tool would tell you if it is with in ECU specific range or not.
#3
Registered
Join Date: Jan 2007
Posts: 1,667
Likes: 0
Received 0 Likes
on
0 Posts
If you have Diacom or something similar, they also make a "sensor test lead kit" that is optional.
It will test your range either installed or not. Often saves you from throwing parts at it.
It's basically the same thing as what is said above but sort of eliminates the need to be smart enough to read meters and know in advance what the numbers are..
It will test your range either installed or not. Often saves you from throwing parts at it.
It's basically the same thing as what is said above but sort of eliminates the need to be smart enough to read meters and know in advance what the numbers are..
Last edited by SDFever; 05-16-2011 at 10:28 AM.
#4
Ginger or Mary Ann?
Charter Member
Thread Starter
Yep, knew it was coolant, but brain fart typed control duhh.
This is just to see if the motor will start with the ECT out of the equation for a fast easy check. Have no scan tools. Does the ECM look for no voltage or 5 volts for a cold start?
This is just to see if the motor will start with the ECT out of the equation for a fast easy check. Have no scan tools. Does the ECM look for no voltage or 5 volts for a cold start?
__________________
Some people are like Slinkies - Not really good for anything, but they
bring a smile to your face when pushed down the stairs.
Some people are like Slinkies - Not really good for anything, but they
bring a smile to your face when pushed down the stairs.
#5
Registered
Join Date: Jan 2007
Posts: 1,667
Likes: 0
Received 0 Likes
on
0 Posts
With no tool it's a guess.
#6
Registered
Join Date: Dec 2004
Location: Indiana/Lake Cumberland
Posts: 186
Likes: 0
Received 0 Likes
on
0 Posts
You can make a simple scan tool for about $5.00, I did. I found out how to make it here, on one of the forums. I would tell you how, if I could remember.
Last edited by 427 larry; 05-16-2011 at 07:27 PM.
#7
Registered
In my foggy old brain, logic would say that it starts at zero for cold and goes up to 5 V, but logic and boats rarely play together. That is probably some type of rheostat on a bi-metal strip much like a temp gauge sender would have, and I'm pretty sure these vary from low to high.
#8
CIRCUIT DESCRIPTION:
The Engine Coolant Temperature (ECT) sensor uses
a thermistor to control the signal voltage to the ECM.
The ECM applies a voltage on CKT 410 to the sensor.
When the engine coolant is cold, the sensor (thermistor)
resistance is high; therefore, the ECM will see
high signal voltage.
As the engine coolant warms, the sensor resistance
becomes less, and the voltage drops.
Start on page 5C-86 for more info about how the sensors work.
http://www.boatfix.com/merc/Servmanl/16/16C5R2.PDF
The Engine Coolant Temperature (ECT) sensor uses
a thermistor to control the signal voltage to the ECM.
The ECM applies a voltage on CKT 410 to the sensor.
When the engine coolant is cold, the sensor (thermistor)
resistance is high; therefore, the ECM will see
high signal voltage.
As the engine coolant warms, the sensor resistance
becomes less, and the voltage drops.
Start on page 5C-86 for more info about how the sensors work.
http://www.boatfix.com/merc/Servmanl/16/16C5R2.PDF
#9
Registered
Join Date: Aug 2005
Location: sint maarten
Posts: 1,491
Likes: 0
Received 0 Likes
on
0 Posts
This sensor, (Engine Coolant Temp) is sending a varible voltage of up to 5V to the ECM to adjust fuel mixture. Can this sender be bypassed by jumping across the 2 wires in the sensor plug, or unplugging the wires, or can't be bypassed, only tested? I'm thinking it will either send a full 5 volts thru, or zero volts. Not sure what voltage the ECM is looking for when cold.
Motor just cranks, no start when cold. After several minutes, it will finally catch, then all is well. A marine mechanic has suggested to check this sensor.
Thanks
Motor just cranks, no start when cold. After several minutes, it will finally catch, then all is well. A marine mechanic has suggested to check this sensor.
Thanks
#10
Ginger or Mary Ann?
Charter Member
Thread Starter
Thanks all
__________________
Some people are like Slinkies - Not really good for anything, but they
bring a smile to your face when pushed down the stairs.
Some people are like Slinkies - Not really good for anything, but they
bring a smile to your face when pushed down the stairs.