Removing Silent Choice Exhaust ???
#21
Banned
Join Date: Aug 2012
Posts: 765
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
Correct the silent choice for sure do not remove!Unless you crawl down canals @900 rpm??Good selling feature also can't see a boat that nice without them!I wired mine open once did not help at all?I replaced flappers&pitch done problem solved
![Whistle](/forums/images/smilies/whistle.gif)
#22
Registered
![](https://www.offshoreonly.com/forums/images/icons/platinum_member_star.gif)
Thread Starter
![Default](/forums/images/icons/icon1.gif)
Not sure I'm following what you're saying. I understand the part about not removing the silent choice but I'm not sure what you're saying you did to correct the problem??
#23
Registered
![Default](/forums/images/icons/icon1.gif)
I have seen where some guys actually run a ball valve with a y-pipe for the seawater pumps so that the pumps could be made to act as an emergency bilge pump. That seawater pump can move a lot of water - might not be a bad safety factor to have if you run a long ways offshore.
#26
Registered
![Default](/forums/images/icons/icon1.gif)
capping them would not be a big deal and if you are concerned about the breaking off, just fab up a bracket over to something to support it till the engines come out and remove the Y-pipe, most are just hooked with a rubber hose anyway so would not need anything to trick..
#27
Registered
![](https://www.offshoreonly.com/forums/images/icons/platinum_member_star.gif)
Thread Starter
![Default](/forums/images/icons/icon1.gif)
I'm not either. I'm sure for many it has been fine and in all likelihood probably would be fine for me too... But, during the season we're out in the ocean at a minimum of once a week... last season we came down so hard off a wave one time that my refrigerator busted off it's mounts through the cabinets and came flying out. In the unlikely event that one or both of those pipes broke loose, I don't think we'd be afloat for long with all that weight in the back... knowing it could be a problem is enough.. and my mechanic said he'd pull my engines for a very reasonable "winter price", so that's the route I'm going. Plus, it will be nice to get access to clean stuff up with the engines out...
#29
Registered
Join Date: Jun 2004
Location: St-Hyacinthe, quebec, canada
Posts: 7,803
Received 399 Likes
on
267 Posts
![Default](/forums/images/icons/icon1.gif)
Question that pops up in my head tonight...
Why would a 525 have issue with water reversion while running silent, meaning the thru hull exhaust are blocked, diverting the pressure in the y pipe, making the exhaust go out from only one hole in the transom plate, and a lets say newer MTI that comes standard from the mold, with only one big hole below the transom plate, for the exhaust to exit below water 100% of time, except on plane of course, and they run big cam engines im sure, and they dont have problem with reversion...
What is different with these animals that avoid water reversion?
Why would a 525 have issue with water reversion while running silent, meaning the thru hull exhaust are blocked, diverting the pressure in the y pipe, making the exhaust go out from only one hole in the transom plate, and a lets say newer MTI that comes standard from the mold, with only one big hole below the transom plate, for the exhaust to exit below water 100% of time, except on plane of course, and they run big cam engines im sure, and they dont have problem with reversion...
What is different with these animals that avoid water reversion?
#30
Registered
![Default](/forums/images/icons/icon1.gif)
they are borderline on reverting at idle, when running thru silent choice picks up the water very easily out of the Y-Pipe, have to remember that the water is at the water line of your boat in the Y-Pipe while sitting or moving slow(found this out the hard way) so until you get moving to get the water out of there it's traps a lot of water in the pipe and thus making it even more prone to reverting...