Fuel pump location
#1
Registered
Thread Starter
![Default](/forums/images/icons/icon1.gif)
I have an aeromotive fuel pump i want to use on a 496 ,I am not sure where to position the pump?
Aeromotive say run the fuel line from the fuel tank to a 100 micron pre filter then fuel line to the pump from the pump a fuel line to the water seperating filter then to fuel rails.
Whipple say to run the fuel line from the fuel tank to the water seperating filter then fuel line to the pump and then to the fuel rails
Aeromotive say run the fuel line from the fuel tank to a 100 micron pre filter then fuel line to the pump from the pump a fuel line to the water seperating filter then to fuel rails.
Whipple say to run the fuel line from the fuel tank to the water seperating filter then fuel line to the pump and then to the fuel rails
#2
Registered
![Default](/forums/images/icons/icon1.gif)
Ayuh,.... Any filters should be on the vacuum side of the pump,.....
#3
Registered
Thread Starter
![Default](/forums/images/icons/icon1.gif)
So the water seperator filter that filters 10 microns should go on the inlet side of the pump even though aeromotive say not to use an inlet filter less than 100 microns
#4
Registered
![Default](/forums/images/icons/icon1.gif)
I put my aeromotive low as possible in the bilge after the merc filter/separator, then the 10 micron in line filter just before it enters the fuel rail. Was told them pumps like to push fuel ,not pull from the tank.
Last edited by camptappakeg69; 05-03-2018 at 06:20 PM.
#5
Registered
Thread Starter
![Default](/forums/images/icons/icon1.gif)
I thought the fuel pump likeed to push the fuel too thats why i thought the smaller 10 micron filter would be better after the pump and the larger 100 micron before the pump
#6
Registered
Join Date: Jul 2008
Location: NORTH TEXAS
Posts: 101
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
I have been down this road. I used to have the 100 micron then then the pump then the water separator to the rail. but this is wrong first you don't want 50lbs of pressure going to the water separator. just scrap your 10 micron completely. go from tank to water separator then to the pump as low as can go and as big a line as you can do. my tank actually has two pickups so I use both into a aeromotive fuel block to a 1/2" or 5/8" line to separator and big to pump then out of pump to rails my rail was modified by Eddie Young and It feeds both ends of the rail on a 502 MPI then out of the rail to the regulator and the return goes back to my fuel tank. I quit using the aeromotive fuel filter completely and I also had a fuel cooler that I know longer use either.
#7
Registered
Thread Starter
![Default](/forums/images/icons/icon1.gif)
Oh great thanks i am installing a whipple and thats how their instructions read.
it was after reading the aeromotive instructions where they say to run a 100 micron filter before the pump that i wasnt sure where to locate the pump
it was after reading the aeromotive instructions where they say to run a 100 micron filter before the pump that i wasnt sure where to locate the pump
#8
Registered
![Default](/forums/images/icons/icon1.gif)
I have been down this road. I used to have the 100 micron then then the pump then the water separator to the rail. but this is wrong first you don't want 50lbs of pressure going to the water separator. just scrap your 10 micron completely. go from tank to water separator then to the pump as low as can go and as big a line as you can do. my tank actually has two pickups so I use both into a aeromotive fuel block to a 1/2" or 5/8" line to separator and big to pump then out of pump to rails my rail was modified by Eddie Young and It feeds both ends of the rail on a 502 MPI then out of the rail to the regulator and the return goes back to my fuel tank. I quit using the aeromotive fuel filter completely and I also had a fuel cooler that I know longer use either.
Last edited by camptappakeg69; 05-04-2018 at 12:27 PM.