Go Back  Offshoreonly.com > Technical > General Q & A
Lab Finishing props ? >

Lab Finishing props ?

Notices

Lab Finishing props ?

Thread Tools
 
Old 04-04-2003, 02:41 PM
  #1  
Registered
Thread Starter
 
Ratchet's Avatar
 
Join Date: Sep 2001
Location: Lake St. Clair
Posts: 353
Likes: 0
Received 0 Likes on 0 Posts
Question Lab Finishing props ?

Ok Guys, I know I have a combination that I don't think anyone else has, so I don't think that I can get any results without trying out props.

However, I'd Like to know what kind of speed / midrange increases do you get with a labbed prop....from searching the board, it looks like it may be 2 or 3 mph. Is this about right ?

My combo is a 31 scarab with 355's pushing shomewhere in the low to mid 400 hp range. Since it has small blocks in the back, it sits a bit higher than the rest of them, so I don't think it needs any stern lift (it flies really nice & level). The boat spins 21 MPs at 6000, and 23's around 54-5500. This gives me 70.4 on GPS.

Anyways, I don't have a lot to spend right now, but I'd like to gain an extra few mph (who doesn't). I really like the punch of the 21's, but like the cruise of the 23's. I also tried a 22 bravo I, with similar results to the 23s.

Any thoughts ?
Ratchet is offline  
Old 04-04-2003, 03:45 PM
  #2  
RLW
~~~~
Charter Member
 
Join Date: Oct 2000
Location: Western New York
Posts: 1,451
Likes: 0
Received 3 Likes on 3 Posts
Default

Darin at HoustonProp can help you on your setup.
Call him at 281-580-7767
His pricing is reasonable.
RLW is offline  
Old 04-05-2003, 12:45 AM
  #3  
Registered
 
HOUSTONPROP's Avatar
 
Join Date: Jul 2002
Location: Houston,texas
Posts: 1,387
Likes: 0
Received 0 Likes on 0 Posts
Default Re: Lab Finishing props ?

Originally posted by Ratchet
Ok Guys, I know I have a combination that I don't think anyone else has, so I don't think that I can get any results without trying out props.

However, I'd Like to know what kind of speed / midrange increases do you get with a labbed prop....from searching the board, it looks like it may be 2 or 3 mph. Is this about right ?

My combo is a 31 scarab with 355's pushing shomewhere in the low to mid 400 hp range. Since it has small blocks in the back, it sits a bit higher than the rest of them, so I don't think it needs any stern lift (it flies really nice & level). The boat spins 21 MPs at 6000, and 23's around 54-5500. This gives me 70.4 on GPS.

Anyways, I don't have a lot to spend right now, but I'd like to gain an extra few mph (who doesn't). I really like the punch of the 21's, but like the cruise of the 23's. I also tried a 22 bravo I, with similar results to the 23s.

Any thoughts ?
Ratchet from what I have gathered from your great information ,I would suggest working the 21 pitch MPs and add alot of cupping/This will maintain the punch and run like a 23 on the top end. If this does not work, I will work the 23 MPs at no cost / one question what are the 21 pitch props running are they at 70.4 at 6000 or are you just talking about the 23s? Thanks Darin
HOUSTONPROP is offline  
Old 04-06-2003, 08:18 PM
  #4  
Registered
Thread Starter
 
Ratchet's Avatar
 
Join Date: Sep 2001
Location: Lake St. Clair
Posts: 353
Likes: 0
Received 0 Likes on 0 Posts
Default

The 21's at 6000 were giving me the 70.4. The 23's ran about the same top end (70.2 was the best I could get last summer ), but spun in the 54-5500 range . However, I liked the cruise with the 23's (saved gas & spun less). The acceration isn't really bad with the 23's (in fact it has more bite with the 23's, which actually lets me get on plane a bit easier..........the 21's tend to blow out if you get on it hard), It's just that the 21's worked well and pulled nicely through the entire RPM range

Maybe what I'll need to do is double check everything once we stop getting this F&%#*ng freezing rain & snow, then give you a call.

Like always, seeking an extra couple MPH.

Thanks Darin, Like I said, I'll call you when I get back out there,
RJ
Ratchet is offline  
Old 04-07-2003, 04:39 AM
  #5  
bvs629
Guest
 
Posts: n/a
Default Re: Re: Lab Finishing props ?

Originally posted by HOUSTONPROP
Ratchet from what I have gathered from your great information ,I would suggest working the 21 pitch MPs and add alot of cupping/This will maintain the punch and run like a 23 on the top end. If this does not work, I will work the 23 MPs at no cost / one question what are the 21 pitch props running are they at 70.4 at 6000 or are you just talking about the 23s? Thanks Darin
Darin,
Do you advise adding some cup to the Bravo 1's 24 pitch we discussed?

BVS629

Dennis
 
Old 05-16-2003, 01:31 AM
  #6  
Registered
 
HOUSTONPROP's Avatar
 
Join Date: Jul 2002
Location: Houston,texas
Posts: 1,387
Likes: 0
Received 0 Likes on 0 Posts
Thumbs up bvs629

Thank You for placing your order on the Bravo one's, we will call you the day they arrive and again thanks Dennis .
/H/P EQUALS HORSEPOWER AND Houston Propeller delivers H/P
HOUSTONPROP is offline  
Old 05-20-2003, 10:21 AM
  #7  
Registered
 
HOUSTONPROP's Avatar
 
Join Date: Jul 2002
Location: Houston,texas
Posts: 1,387
Likes: 0
Received 0 Likes on 0 Posts
Default bvs629

props are with the man in brown.
HOUSTONPROP is offline  
Old 05-21-2003, 06:06 PM
  #8  
bvs629
Guest
 
Posts: n/a
Talking Re: Re: Re: Lab Finishing props ?

Originally posted by bvs629
Darin,
Do you advise adding some cup to the Bravo 1's 24 pitch we discussed?

BVS629

Dennis
Looking forward to the return and running them this Memorial weekend!!

DW
 
Old 05-21-2003, 07:37 PM
  #9  
Registered
 
Join Date: Mar 2002
Location: Boydton Va.
Posts: 1,089
Likes: 0
Received 0 Likes on 0 Posts
Default

Call Throttle-Up Props. 727 531-2255

They are the BEST.
HighPriority is offline  
Old 05-21-2003, 11:08 PM
  #10  
Registered
 
HOUSTONPROP's Avatar
 
Join Date: Jul 2002
Location: Houston,texas
Posts: 1,387
Likes: 0
Received 0 Likes on 0 Posts
Thumbs up Re: Re: Re: Re: Lab Finishing props ?

Originally posted by bvs629
Looking forward to the return and running them this Memorial weekend!!

DW
Dennis ,Iworked the bravo ones as we discussed ,lab and yes I did add a touch of cupping on the pitch section ,no rake was added,they are balanced on the money and hope you enjoy them ,Thanks again for the Business.Darin Houston Prop.281- 580-PROP
HOUSTONPROP is offline  


Quick Reply: Lab Finishing props ?


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.