Nosecones...Are they worth it?
#1
Registered
Thread Starter
Join Date: Jan 2004
Location: Long Island NY.
Posts: 450
Likes: 0
Received 0 Likes
on
0 Posts
Nosecones...Are they worth it?
I put a Hydromotive nosecone on my OMC Cobra drive a couple of years ago. Can't say I saw (or felt) any difference. But then again, my boat is only in the low 60's. Did I waste my time?
#3
Platinum Member
Platinum Member
On a 90mph drag outboard, I lost 2 boat lengths on holeshot and was still picking up speed thru the traps.
Took the cone back off and picked up all that had been lost. I added it to an XR4 2:1 gearcase for dragging, but couldn't keep water pressure up. After the bad cone episode, I ground "tracks" in the sides of the case to lift the water to the pickups. Got my speed back and got my water pressure back.
Got real mixed feelings on cones...
Took the cone back off and picked up all that had been lost. I added it to an XR4 2:1 gearcase for dragging, but couldn't keep water pressure up. After the bad cone episode, I ground "tracks" in the sides of the case to lift the water to the pickups. Got my speed back and got my water pressure back.
Got real mixed feelings on cones...
#4
Registered
After running the same boat with and without nosecones with various power I have concluded on my own experience that it depends on the hull. If your hull likes stern lift and carries the bow very well with little positive trim you may gain something. If you have trouble carrying the bow and stern lift forces the bow down you will probably lose speed. My hull has hooks in it (they are coming out this winter) and the bow does not carry well above 60 the nose cones added stern lift and caused the bow to sink as speed increased. On occasion with the right chop and wind it would pop up and carry until conditions let it drop I did see some gain. Sort of like a teeter todder. May not be hurting you at 60. Steering seemed as it it had more of a tendency to grab in hard turns.
#5
Charter Member #232
Charter Member
You do not want them as I understand with Bravo's unless you are going over 75-80 and TRS drives if you are going 80-85. Anything slower you will likely loose speed by putting them on.
Jon
Jon
__________________
Put your best foot forward!
Put your best foot forward!
#6
Charter Member
Charter Member
Join Date: Oct 2000
Location: Central, Ohio USA
Posts: 1,074
Likes: 0
Received 0 Likes
on
0 Posts
On an Eliminator 28" Daytona with Bravos, the cones started making a difference about 85 mph. We had one drive with a cone and one without running at the same time. By 90 mph, the throttles were pretty far apart and the drive without the cone was gaining a ton of rpm compared to the one with the cone.
Below 85, both drives ran about the same.
Below 85, both drives ran about the same.
#7
Registered
Thread Starter
Join Date: Jan 2004
Location: Long Island NY.
Posts: 450
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for the input. I have the cone on an OMC Cobra drive, which I'm sure you guys aren't using. Unfortunately, when I put the cone on, it was with the old engine which was slowly dying, so I couldn't tell if it made any change. I have noticed with the new engine, that I do tend to run a lot of positive trim. Actually, the engine story would be a good one. I'll have to post it one day. How hard is it to get the cones off??
#8
Registered
Join Date: Feb 2002
Location: Honeoye, NY
Posts: 763
Likes: 0
Received 0 Likes
on
0 Posts
Just removed two; one welded -- one just epoxied. The welded one was actually easier cause it was only tacked and a die grinder took care of that -- then WHACK and it's off. For the full epoxy installation, you gotta use heat and then WHACK. --- Jer
#10
Geronimo36
Gold Member
Originally posted by mcollinstn
Sledge hamma.
Not a baby tap, BIIG smack.
Sledge hamma.
Not a baby tap, BIIG smack.
I heated mine with a torch just to get the epoxy a little soft, the whackaroo. I had both of them off in about 10 minutes. An added benefit later was the left over epoxy filled in some of the pit marks that were under there.