How complicated is it to bebuild a Rochester Q-Jet
#1
Registered
Thread Starter
Join Date: Nov 2003
Location: Lanoka Harbor, NJ
Posts: 3,354
Likes: 0
Received 0 Likes
on
0 Posts
![Question](/forums/images/icons/icon5.gif)
Hope this question isn't too pathetic
((the stupidest question is the one not asked, right
)) I need to rebuild my 2 Q-Jets and wondering if it's a job I can do myself? I've got the carbs off ... good start LOL and looking to buy this kit on Ebay?? and can handle most all other mechanical jobs I've attempted. So is it simple or ????
I've got to begin doing this stuff myself. 2 engines, 2X the problems, 2 chances to get it right!
![Stick Out Tongue](/forums/images/smilies/tongue.gif)
Thanks for any and all help, encouragement, or suggestions.
![Roll Eyes (Sarcastic)](/forums/images/smilies/rolleyes.gif)
![Big Grin](/forums/images/smilies/biggrin.gif)
I've got to begin doing this stuff myself. 2 engines, 2X the problems, 2 chances to get it right!
![Big Grin](/forums/images/smilies/biggrin.gif)
![Big Grin](/forums/images/smilies/biggrin.gif)
![Stick Out Tongue](/forums/images/smilies/tongue.gif)
Thanks for any and all help, encouragement, or suggestions.
#2
Registered
Join Date: Nov 2003
Location: Fairhaven Ma
Posts: 833
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
Not too bad. Pickup a merc sevice manual and take your time(cleaning and paying attention to parts locations). The kits from merc are 22.00 bucks (cheap). They come with a float level indicator and needle/seat. If the metering rods look corroded merc has a kit for that. The genuine merc manuals are the best for carbs too. Also the screws losen up that connect the throttle plates to the bowl housing.
#3
Guest
Posts: n/a
![Default](/forums/images/icons/icon1.gif)
I would find out if the kits are OEM or after market. The parts in an OEM kit are better quality. As far as rebuilding they are not too tough. Do one at a time and you can always look at the other one. If you have any question just ask me I have been rebuilding them for 25 years.
#4
Registered
Join Date: Nov 2001
Location: Pennsylvania
Posts: 3,385
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
Do it yourself and take the advise from the guys above. This will be a very satisfying undertaking I suspect. If you run into trouble OSO is only a few clicks away.. Just a couple words of caution, check the diameter of the new needle/seat. Often qjet rebuild kits come with a n/s sized more appropriate for automotive. Secondly,If you decide to paint your finished carbs, only spray the sides, none on the choke plates or in the air intake area. Lastly, loctite the screws that go into the underside of the carb. You wouldn't want one of these falling out.
Dave
Dave
#5
Registered
Thread Starter
Join Date: Nov 2003
Location: Lanoka Harbor, NJ
Posts: 3,354
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
Thanks guys!
marinetrans, do you have a link for Merc kits for $22 or know where?? Also the manuals?? I'm searching around too, just thought you might have a source for these![Smilie](/forums/images/smilies/smile.gif)
Thanks meyerwrench .. 25 yrs sounds like a career .. where you located lol!![Big Grin](/forums/images/smilies/biggrin.gif)
Hey Dave, yeah i hope to have a few of these 'satisfying undertakings' in the near future, these bring the first 2 of many .. thx for tips and encouragement!![Smilie](/forums/images/smilies/smile.gif)
I'll be back!! Don't go anywhere. hehe
marinetrans, do you have a link for Merc kits for $22 or know where?? Also the manuals?? I'm searching around too, just thought you might have a source for these
![Smilie](/forums/images/smilies/smile.gif)
Thanks meyerwrench .. 25 yrs sounds like a career .. where you located lol!
![Big Grin](/forums/images/smilies/biggrin.gif)
Hey Dave, yeah i hope to have a few of these 'satisfying undertakings' in the near future, these bring the first 2 of many .. thx for tips and encouragement!
![Smilie](/forums/images/smilies/smile.gif)
I'll be back!! Don't go anywhere. hehe
#6
Registered
Join Date: Nov 2003
Location: Fairhaven Ma
Posts: 833
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
You can get the kit from a local merc dealer. Merc pn#823426A1. Far as the manual, give the merc dealer a serial # of your motor or year and they can look it up in merc's publications book.
#8
Ginger or Mary Ann?
![](https://www.offshoreonly.com/forums/images/icons/charter_member_star.gif)
![Default](/forums/images/icons/icon1.gif)
I have called Mercury Marine publishing and got the factory service manual specifically for my motor. I think it was only around $25. Just give them your serial number. It is a great manual, covers everything from flame arrestor nut to oil drain screw in detail. Highly recommend them.
__________________
Some people are like Slinkies - Not really good for anything, but they
bring a smile to your face when pushed down the stairs.
Some people are like Slinkies - Not really good for anything, but they
bring a smile to your face when pushed down the stairs.
#9
Charter Member
![](https://www.offshoreonly.com/forums/images/icons/charter_member_star.gif)
![Default](/forums/images/icons/icon1.gif)
When you do the Q-jets make sure you epoxy the bowl plugs on the bottom. There are 2 lead plugs under the bowl that will leak and cause rich starts. Easy to do and will make them work better in the long run.
#10
Registered
![Default](/forums/images/icons/icon1.gif)
Originally posted by insptech
When you do the Q-jets make sure you epoxy the bowl plugs on the bottom. There are 2 lead plugs under the bowl that will leak and cause rich starts. Easy to do and will make them work better in the long run.
When you do the Q-jets make sure you epoxy the bowl plugs on the bottom. There are 2 lead plugs under the bowl that will leak and cause rich starts. Easy to do and will make them work better in the long run.
Roby