Arizona Speed & Marine 625 HP engine
03-09-2004, 01:09 PM
#1
Registered
Thread Starter
Arizona Speed & Marine 625 HP engine
Does anyone have any experience (good/bad/otherwise) with this engine?
From Arizona Speed & Marine's website:
625 HP on 87 Octane!! VORTEC L-18 engine
**Headers are not included**
Engine Dynoed 625 HP and 675 ft/lbs Torque
Replicated intake port manifold desing incorporates cross ram tuning.
Large 85 MM billet throttle valve includes progressive action for smooth tip-in.
Low overall height, 1" taller than stock.
Re-designed cylinder heads have large stainless steel intake valves, inconel exhaust valves.
Hydraulic roller billet camshaft with full rollerized rocker arms.
high capacity oil pan, two piece design with windage tray.
Knock sensor, rev-limit, and temperature protection programmed in ECU.
MSD 8.5 MM spark plug wires.
Retail: $25,000.00Your Price: $21,900.00
From Arizona Speed & Marine's website:
625 HP on 87 Octane!! VORTEC L-18 engine
**Headers are not included**
Engine Dynoed 625 HP and 675 ft/lbs Torque
Replicated intake port manifold desing incorporates cross ram tuning.
Large 85 MM billet throttle valve includes progressive action for smooth tip-in.
Low overall height, 1" taller than stock.
Re-designed cylinder heads have large stainless steel intake valves, inconel exhaust valves.
Hydraulic roller billet camshaft with full rollerized rocker arms.
high capacity oil pan, two piece design with windage tray.
Knock sensor, rev-limit, and temperature protection programmed in ECU.
MSD 8.5 MM spark plug wires.
Retail: $25,000.00Your Price: $21,900.00
03-11-2004, 03:56 PM
#2
Registered
Join Date: Jan 2004
Location: San Diego, California
Posts: 2,777
Likes: 0
Received 6 Likes
on
6 Posts
DamnDonzi:
I was in the booth with Jim at AS&M in Miami and Those engines are nice pieces with a lot of work and tech in them .Jim seems like the kind of guy who is not a bull****er! I would just ask for the dyno documentation sheets on the engine and if they show 625Hp I would bet it might be a good number. Remember these motors have forged pistons, are bored and stroked for about 525 cubic inch with nice internals. The pricing he offers on his special on the website seems like a great price and I would guess you will be happy. Just don't forget to add the $5,000 grand for the CMI type exhaust, I am sure thats probably how they were dynoed for those numbers. Ask Jim for a refferral to one of his Havasu customers who is running the motor. Just a few thoughts.
Raylar
I was in the booth with Jim at AS&M in Miami and Those engines are nice pieces with a lot of work and tech in them .Jim seems like the kind of guy who is not a bull****er! I would just ask for the dyno documentation sheets on the engine and if they show 625Hp I would bet it might be a good number. Remember these motors have forged pistons, are bored and stroked for about 525 cubic inch with nice internals. The pricing he offers on his special on the website seems like a great price and I would guess you will be happy. Just don't forget to add the $5,000 grand for the CMI type exhaust, I am sure thats probably how they were dynoed for those numbers. Ask Jim for a refferral to one of his Havasu customers who is running the motor. Just a few thoughts.
Raylar
10-30-2004, 04:58 PM
#4
Charter Member #232
Charter Member
Re: Arizona Speed & Marine 625 HP engine
You should contact Biggus on the board and get Timmy Dorres number up in Maine. He made Kurts motors and they are running perfectly. Plus you can not put a price on local when dealing with engines. I think that he is the authorized repair place for Cheaf also.
Jon
Jon
__________________
Put your best foot forward!
Put your best foot forward!
Thread
Thread Starter
Forum
Replies
Last Post
enticer
General Boating Discussion
15
08-05-2002 03:44 PM
