SBC valve guide/seal leakage?
#1
Registered
Thread Starter
Join Date: Jul 2001
Location: SW Ohio
Posts: 770
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
Just pulled my heads off to have a complete valve job done. I noticed that most of the exhaust valves in the port area were covered in some way with rings or streaks/smears of oil. My question is this. Should there be ANY oil on ANY part of the exhaust valves? I have attached some pics.
Thanks
Randy
Thanks
Randy
Last edited by BAD-HABIT; 04-07-2004 at 06:35 AM.
#3
Registered
Thread Starter
Join Date: Jul 2001
Location: SW Ohio
Posts: 770
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
This pic if you look closely shows also what several of the valves have. Which is a portion of the valve with a coating of oil. It is darker in color than the rest of the valve and slightly wet with and oily substance.
Last edited by BAD-HABIT; 04-07-2004 at 06:22 AM.
#6
![Default](/forums/images/icons/icon1.gif)
Look ok to me >I have seen them leave trails out the port before.You do want some oil so the guild want seez
__________________
.
The Only Time You Have To Much Ammo Is When Your Swimming Or On Fire.
.
The Only Time You Have To Much Ammo Is When Your Swimming Or On Fire.
#7
Registered
Thread Starter
Join Date: Jul 2001
Location: SW Ohio
Posts: 770
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
Well thats good to know. But why would different valves have different amouts of oil on them. Also the valves with the most oil on them had coresponding amounts of oil on the threads of the plugs. The valves with less oil on them had less oil on the plug threads. These heads only have about 70 Hours on them.One other note the intake valves all looked pretty clean. It was the exhaust valves that had the oil on them. Does this make a change in your thoughts Strip? Anybody else want to chime in?
Thanks again
Randy
"Bad-Habit"
Thanks again
Randy
"Bad-Habit"
#8
![Default](/forums/images/icons/icon1.gif)
The exhaust gets all the heat so it prob has the most wear to the guild and seal. not shure about the spark plug I have had one motor that did it but never had any prob with any oil in it. maybe the threads are a little worn on it??
I am curios about the oil on the thread also.
In this pick I burned the oil off this one
I am curios about the oil on the thread also.
In this pick I burned the oil off this one
![EEK!](/forums/images/smilies/eek.gif)
![EEK!](/forums/images/smilies/eek.gif)
![Big Grin](/forums/images/smilies/biggrin.gif)
__________________
.
The Only Time You Have To Much Ammo Is When Your Swimming Or On Fire.
.
The Only Time You Have To Much Ammo Is When Your Swimming Or On Fire.
#9
![Default](/forums/images/icons/icon1.gif)
Don't be so surprised with problems with sbc guides.
The real solution is to install positive seals involving machining the guides and also installing bronze guides. With all the motors I've been involved in , this is the only real solution as pertains to head issues.BBB
The real solution is to install positive seals involving machining the guides and also installing bronze guides. With all the motors I've been involved in , this is the only real solution as pertains to head issues.BBB
#10
Registered
Join Date: Dec 2003
Location: Los Angeles California
Posts: 8,306
Likes: 0
Received 2 Likes
on
2 Posts
![Default](/forums/images/icons/icon1.gif)
Some people are thrilled to death to have a little oil going down the exhaust valve guide to lubricate things... It's the intake that usually gets too much oil coming down the guide due to vacuum from the manifold... then you see coking on the underside of the valve. How does the underside of the exhaust valve look?... The picture only showed the stem.