trim pump slowdown mean dying????
#1
Registered
Thread Starter
Join Date: Feb 2004
Location: Murray,KY
Posts: 487
Likes: 0
Received 0 Likes
on
0 Posts
trim pump slowdown mean dying????
one of my pumps is very slow and getting slower as if in a bind somewhere(drive was off not long ago)or voltage is low.(both batt used on both)I guess this means the motor is going bad?Can I buy the mtr seperately? or should I just get the whole unit.Thanks
#3
Platinum Member
Platinum Member
Join Date: Nov 2003
Location: Stockholm, Sweden
Posts: 528
Likes: 0
Received 0 Likes
on
0 Posts
Re: trim pump slowdown mean dying????
Exactly the same happened to me today!
I'm going to tear down the motor tomorrow or Tuesday to figure out the problem.
I'll let you know.
I'm going to tear down the motor tomorrow or Tuesday to figure out the problem.
I'll let you know.
#5
Registered
Thread Starter
Join Date: Feb 2004
Location: Murray,KY
Posts: 487
Likes: 0
Received 0 Likes
on
0 Posts
Re: trim pump slowdown mean dying????
fluid level is barely below MIN with outdrive all the way up??Seems like if it were low fluid the motor would spin faster and not move the drive?
#6
Platinum Member
Platinum Member
Join Date: Nov 2003
Location: Stockholm, Sweden
Posts: 528
Likes: 0
Received 0 Likes
on
0 Posts
Re: trim pump slowdown mean dying????
My motor was getting slower and slower and finally died.
The fluid level is perfect so I'm quite sure it is a motor failure.
The fluid level is perfect so I'm quite sure it is a motor failure.
#7
Registered
Join Date: Aug 2002
Location: Eastern Lake Ontario
Posts: 2,896
Likes: 0
Received 3 Likes
on
3 Posts
Re: trim pump slowdown mean dying????
It's definitely the motor. Same thing happened to mine. Motor bad on one of my trim pumps and another bad on one of my K-plane pumps. Had them both rebuilt at an alternator/starter rebuild shop. Didn't cost much and now they all work well. Actually, the newely rebuilt ones are a little faster then the non-rebuilt ones. I should pull the other two.
Do the motors, I'm sure thats the problem and not the pumps.
Do the motors, I'm sure thats the problem and not the pumps.
#8
Registered
Thread Starter
Join Date: Feb 2004
Location: Murray,KY
Posts: 487
Likes: 0
Received 0 Likes
on
0 Posts
Re: trim pump slowdown mean dying????
Thanks,I was wondering if they could be rebuilt. We have a good/cheap little alt shop down the street. It's never this easy with boats.
#9
Platinum Member
Platinum Member
Join Date: Nov 2003
Location: Stockholm, Sweden
Posts: 528
Likes: 0
Received 0 Likes
on
0 Posts
Re: trim pump slowdown mean dying????
I took my motor apart yesterday and the brushes was totally gone.
Cleaned it and installed new brushes today, runs like new!
Cleaned it and installed new brushes today, runs like new!
#10
Registered
Join Date: Oct 2000
Location: Chesterfield Mo/Loto
Posts: 1,381
Likes: 0
Received 11 Likes
on
2 Posts
Re: trim pump slowdown mean dying????
Originally Posted by 38KV
I took my motor apart yesterday and the brushes was totally gone.
Cleaned it and installed new brushes today, runs like new!
Cleaned it and installed new brushes today, runs like new!
KV were did you purchase the brushes from. i have a motor that keeps quitting on me untill i go back and tap on it. i actually had a old motor laying around a swapped them out and works fine so i was thinking i'll replace the brushs for a spare.
later