combat zone 24 restoration
#132
Registered
Thread Starter
Join Date: Aug 2010
Location: MA
Posts: 2,535
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
@ rick. Dont worry we'll get her dialed with big power for next season. If you'd like ill make a special trip to put ya over my knee![Lolhit](/forums/images/smilies/more/lolhit.gif)
Thanks catlyst....motors for sale. Would be a good candidate for ya excalibur $6500 with fresh gaskets & whatever else it takes to get it back to 100%. Complete pan to carb
![Lolhit](/forums/images/smilies/more/lolhit.gif)
Thanks catlyst....motors for sale. Would be a good candidate for ya excalibur $6500 with fresh gaskets & whatever else it takes to get it back to 100%. Complete pan to carb
![Evil](/forums/images/smilies/evilB.gif)
#133
Registered
![Default](/forums/images/icons/icon1.gif)
tempting but my shortblock is half way done over at precision an i doubt i have the bulkhead clearance for a blower excal has a small engine bay. on another note got any heads lying around for sale?
#134
Registered
![Default](/forums/images/icons/icon1.gif)
Great effort Mike! Don't blow your brains out on big power. I was given good advice recently. "You got to finish the race." I look forward to catching up at some point. Good luck with the other stuff you got going this summer.
#135
![Default](/forums/images/icons/icon1.gif)
@ rick. Dont worry we'll get her dialed with big power for next season. If you'd like ill make a special trip to put ya over my knee![Lolhit](/forums/images/smilies/more/lolhit.gif)
Thanks catlyst....motors for sale. Would be a good candidate for ya excalibur $6500 with fresh gaskets & whatever else it takes to get it back to 100%. Complete pan to carb![Evil](/forums/images/smilies/evilB.gif)
![Lolhit](/forums/images/smilies/more/lolhit.gif)
Thanks catlyst....motors for sale. Would be a good candidate for ya excalibur $6500 with fresh gaskets & whatever else it takes to get it back to 100%. Complete pan to carb
![Evil](/forums/images/smilies/evilB.gif)
![Evil](/forums/images/smilies/evilB.gif)
[YOUTUBE]http://www.youtube.com/watch?v=ZayKG5irCEg[/YOUTUBE]
Last edited by rchevelle71; 07-27-2012 at 11:03 PM.
#136
Registered
Thread Starter
Join Date: Aug 2010
Location: MA
Posts: 2,535
Likes: 0
Received 0 Likes
on
0 Posts
I left my brains behind when I started this build, so no worries on the big power. I figure wtf...ive come this far.
Call u soon. Sorry, been crazy busy.
MD
#137
Registered
![Default](/forums/images/icons/icon1.gif)
when you cut the pipes down did you weld the inners to outers and put the upper and lower drain holes back in.
i want to have my gil dry pipes welded around the perimeters and keep the drain holes, just wondering about pressure issues w/o water sneaking out of the swaged ends.
looks really nice, good luck getting dialed in
dan
i want to have my gil dry pipes welded around the perimeters and keep the drain holes, just wondering about pressure issues w/o water sneaking out of the swaged ends.
looks really nice, good luck getting dialed in
dan
#138
Registered
Thread Starter
Join Date: Aug 2010
Location: MA
Posts: 2,535
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
Ya dan ill get a pic.
They look pretty sick now. Factory pipes are crushed together and welded.
We cut & filled the gap welding, then ground it clean. Drilled a couple relief pee holes.
Im pulling em to move the bungs inside the boat this winter I think.
MD
They look pretty sick now. Factory pipes are crushed together and welded.
We cut & filled the gap welding, then ground it clean. Drilled a couple relief pee holes.
Im pulling em to move the bungs inside the boat this winter I think.
MD
#140
![Default](/forums/images/icons/icon1.gif)
@ rick. Dont worry we'll get her dialed with big power for next season. If you'd like ill make a special trip to put ya over my knee![Lolhit](/forums/images/smilies/more/lolhit.gif)
Thanks catlyst....motors for sale. Would be a good candidate for ya excalibur $6500 with fresh gaskets & whatever else it takes to get it back to 100%. Complete pan to carb![Evil](/forums/images/smilies/evilB.gif)
![Lolhit](/forums/images/smilies/more/lolhit.gif)
Thanks catlyst....motors for sale. Would be a good candidate for ya excalibur $6500 with fresh gaskets & whatever else it takes to get it back to 100%. Complete pan to carb
![Evil](/forums/images/smilies/evilB.gif)
![Evil](/forums/images/smilies/evilB.gif)
![](http://i1036.photobucket.com/albums/a443/rchevelle71/mtr2.jpg)
![](http://i1036.photobucket.com/albums/a443/rchevelle71/mtr1.jpg)
![](http://i1036.photobucket.com/albums/a443/rchevelle71/mtr3.jpg)