new bolster / interior build
#1
Registered
Thread Starter
![Default](/forums/images/icons/icon1.gif)
so the boat is the old HART THROB, purpose built no cabin crash bulkhead race boat from the mid 90's and hasn't been in the water since then !
i wanted to do the original owner builder and the boat justice by keeping it in race trim but w/ a little pleasure in the mix.
[ATTACH=CONFIG]563202[/ATTACH][ATTACH=CONFIG]563203[/ATTACH][ATTACH=CONFIG]563204[/ATTACH][ATTACH=CONFIG]563205[/ATTACH]
i wanted to do the original owner builder and the boat justice by keeping it in race trim but w/ a little pleasure in the mix.
[ATTACH=CONFIG]563202[/ATTACH][ATTACH=CONFIG]563203[/ATTACH][ATTACH=CONFIG]563204[/ATTACH][ATTACH=CONFIG]563205[/ATTACH]
#2
Registered
Thread Starter
![Default](/forums/images/icons/icon1.gif)
the engine hatch / compartment was extended approx 21 inches so this is the frame work for the whole cockpit interior dash to fire wall
[ATTACH=CONFIG]563206[/ATTACH][ATTACH=CONFIG]563207[/ATTACH][ATTACH=CONFIG]563208[/ATTACH][ATTACH=CONFIG]563209[/ATTACH][ATTACH=CONFIG]563210[/ATTACH]
21 5/8 inches on the extension, just went out and measured
[ATTACH=CONFIG]563206[/ATTACH][ATTACH=CONFIG]563207[/ATTACH][ATTACH=CONFIG]563208[/ATTACH][ATTACH=CONFIG]563209[/ATTACH][ATTACH=CONFIG]563210[/ATTACH]
21 5/8 inches on the extension, just went out and measured
Last edited by outonsafari; 01-02-2017 at 10:32 AM.
#4
Registered
Thread Starter
#5
Registered
Thread Starter
![Default](/forums/images/icons/icon1.gif)
[ATTACH=CONFIG]563211[/ATTACH][ATTACH=CONFIG]563212[/ATTACH][ATTACH=CONFIG]563213[/ATTACH][ATTACH=CONFIG]563214[/ATTACH]
these should have been the pics from post 1
these should have been the pics from post 1
Last edited by outonsafari; 01-02-2017 at 12:11 PM.
#6
Registered
Thread Starter
![Default](/forums/images/icons/icon1.gif)
was talking to a member on here about the original 3 man bolster, 6 1/2' wide 3' deep 2 1/2' tall, it took 2 guys to get it out of the boat and when stood upright like a refrigerator 1 guy could pick it up for a few seconds and thats about all you could do w/ it. it was HEAVY, so it was suggested to make a 2 man bolster f1 style, i liked the idea, ran w/ it and bought some nida core.
6 thanks that was some good advice
bear w/ me getting the pics up
6 thanks that was some good advice
bear w/ me getting the pics up
Last edited by outonsafari; 01-02-2017 at 11:39 AM.
#7
Registered
![Default](/forums/images/icons/icon1.gif)
Cool looking boat,what's up with the midget striper pole with lights.
![Big Grin](/forums/images/smilies/biggrin.gif)
#8
Registered
Thread Starter
#9
Registered
Thread Starter
![Default](/forums/images/icons/icon1.gif)
[ATTACH=CONFIG]563235[/ATTACH][ATTACH=CONFIG]563236[/ATTACH][ATTACH=CONFIG]563237[/ATTACH][ATTACH=CONFIG]563238[/ATTACH][ATTACH=CONFIG]563239[/ATTACH]
and of course their out of order and upside down
and of course their out of order and upside down
#10
Registered
Thread Starter
![Default](/forums/images/icons/icon1.gif)
[ATTACH=CONFIG]563242[/ATTACH][ATTACH=CONFIG]563243[/ATTACH][ATTACH=CONFIG]563244[/ATTACH][ATTACH=CONFIG]563245[/ATTACH][ATTACH=CONFIG]563246[/ATTACH][ATTACH=CONFIG]563247[/ATTACH][ATTACH=CONFIG]563248[/ATTACH][ATTACH=CONFIG]563249[/ATTACH][ATTACH=CONFIG]563250[/ATTACH]
so all the bracing was bedded down w/ 1/2 wide strips of 1 1/2 ounce csm and cabosil
then i started tabbing it together
so all the bracing was bedded down w/ 1/2 wide strips of 1 1/2 ounce csm and cabosil
then i started tabbing it together
Last edited by outonsafari; 01-02-2017 at 11:10 AM.