81 Scarab project from hell
#431
Registered
![Default](/forums/images/icons/icon1.gif)
At least its fresh water!! Boat looks great in the water. Check your exhaust clamps...mine were leaking when I launched mine the first time. If its real low then it could be the things you suggested. Hopefully it isin't the transom assembly.
#432
Registered
Thread Starter
Join Date: Jul 2005
Location: Spokane, Washington
Posts: 395
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
![EEK!](/forums/images/smilies/eek.gif)
#433
Registered
Join Date: Aug 2007
Location: Sandown, NH - Sebago Lake Region, ME
Posts: 2,960
Likes: 0
Received 7 Likes
on
7 Posts
![Default](/forums/images/icons/icon1.gif)
![Evil](/forums/images/smilies/evilB.gif)
The boat looks awesome scott. In regards to the leak, definetly check the shaft bellow. I just replaced mine and twice almost tightned the clamp down with the lip in the bellow not fully into the groove. Did you actully get to bring her on plane or did you keep it close to the dock?
#434
Registered
Thread Starter
Join Date: Jul 2005
Location: Spokane, Washington
Posts: 395
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
No- I never took it off the trailer- it was getting late and all I wanted to do was see if it was going to leak. Hopefully I will be able to get it out and play with it later this week, its not leaking that bad
![Drink](/forums/images/smilies/drink.gif)
#435
Banned
Join Date: Oct 2006
Location: Bradenton Florida
Posts: 5,927
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
FIX IT !!!!!!
Not that hard !
![Ernaehrung004](/forums/images/smilies/ernaehrung004.gif)
#438
Registered
Thread Starter
Join Date: Jul 2005
Location: Spokane, Washington
Posts: 395
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
100000 starving comedians in the world and you guys are trying to be one![Drink](/forums/images/smilies/drink.gif)
I pulled the hydraulic blocks out- the gasket was good but there was a lot of water in there- so I am going to reseal it. Should I run a bid of RTV around the transom for good measure? I RTV's the sh*t out of the corks and transom plates when I put them back together. I also checked the bellows and they look good- so if resealing the blocks doesn't cure the leak it must be in the transom plate.
I also worked on the rear hatch cover- got it cut, just need to figure out hinges and measure for the ram- hopefully tonight I will have some more photos.
![Drink](/forums/images/smilies/drink.gif)
I pulled the hydraulic blocks out- the gasket was good but there was a lot of water in there- so I am going to reseal it. Should I run a bid of RTV around the transom for good measure? I RTV's the sh*t out of the corks and transom plates when I put them back together. I also checked the bellows and they look good- so if resealing the blocks doesn't cure the leak it must be in the transom plate.
I also worked on the rear hatch cover- got it cut, just need to figure out hinges and measure for the ram- hopefully tonight I will have some more photos.
![Food Smiley 007](/forums/images/smilies/food-smiley-007.gif)