Back from the Dead; '81 Scarab 38 Resto
09-19-2022, 09:02 AM
#1361
VIP Member
VIP MemberThread Starter
Well you guys know how it works with me, I got busy and we’re still working on the instrument panel, I got a lot done on the engine compartment over the weekend, all I lack now is water hoses from strainers to the pumps, wiring the ignition, crankcase ventilation to the spark arrestors, connecting the throttle cables to carb linkage, wiring the trim pumps, and whatever else I can’t think of right now…
The following 8 users liked this post by hblair:
AllDodge (09-19-2022), Knot 4 Me (09-19-2022), larslindroth (10-04-2022), outonsafari (10-12-2022), rak rua (09-19-2022), resurrected (09-22-2022), Stuckonstupid (09-19-2022), Wally (09-21-2022)
The following 2 users liked this post by jeff32:
Helmwurst (09-20-2022), resurrected (09-22-2022)
The following users liked this post:
hblair (10-04-2022)
10-04-2022, 01:21 PM
#1366
VIP Member
VIP MemberThread Starter
Thanks guys, we’ve been getting a fair amount done lately. Shon’s been buried in the wiring.
Also got the cabin hatches sealed and screwed down as well as the bow rail sealed to the deck. Brian’s been helping a lot lately too. We got the throttle linkages connected, fuel hoses run, etc.
We got the port motor setup and started it last night. I figured I’d have a few oil leaks, water leaks, etc. Nothing so far. When we first started it and ran if for prolly a minute, I looked at the gauges and saw oil at 0. Killed the ignition, just about puked in my mouth and was thinking of selling the boat unfinished with a bad motor.
Then Shon asked if I was looking at oil pressure or oil temp. I completely forgot about the oil temp gauge which was, in fact, what I was looking at. Fired it back up, we have 50 psi at idle. It runs good. Little rich but we’ll address that. No leaks at all. Heres a video of it running today…
Also got the cabin hatches sealed and screwed down as well as the bow rail sealed to the deck. Brian’s been helping a lot lately too. We got the throttle linkages connected, fuel hoses run, etc.
We got the port motor setup and started it last night. I figured I’d have a few oil leaks, water leaks, etc. Nothing so far. When we first started it and ran if for prolly a minute, I looked at the gauges and saw oil at 0. Killed the ignition, just about puked in my mouth and was thinking of selling the boat unfinished with a bad motor.
Then Shon asked if I was looking at oil pressure or oil temp. I completely forgot about the oil temp gauge which was, in fact, what I was looking at. Fired it back up, we have 50 psi at idle. It runs good. Little rich but we’ll address that. No leaks at all. Heres a video of it running today…
Last edited by hblair; 10-04-2022 at 02:02 PM.
The following 13 users liked this post by hblair:
1983ScarabIII (10-09-2022), AllDodge (10-04-2022), J-Bonz (10-09-2022), Knot 4 Me (10-04-2022), larslindroth (10-11-2022), outonsafari (10-12-2022), Pappa_Bear98 (10-04-2022), rak rua (10-04-2022), resurrected (10-05-2022), Stuckonstupid (10-04-2022), Topshelf38 (10-05-2022), Wally (10-04-2022), Wildman_grafix (10-04-2022)
The following users liked this post:
hblair (10-09-2022)
10-04-2022, 03:55 PM
#1368
Registered
Sounds sweet
The following users liked this post:
hblair (10-09-2022)
10-09-2022, 07:01 PM
#1369
VIP Member
VIP MemberThread Starter
Thanks guys. Both motors came to life today…
The following 15 users liked this post by hblair:
1983ScarabIII (10-09-2022), hogie roll (10-18-2022), jeff32 (10-09-2022), JKetels (11-01-2022), Kefurr (10-10-2022), Knot 4 Me (10-09-2022), larslindroth (10-11-2022), outonsafari (10-12-2022), rak rua (10-09-2022), resurrected (10-11-2022), SB (10-16-2022), Stuckonstupid (10-10-2022), Tiki Joe (10-10-2022), Topshelf38 (10-11-2022), Wally (10-11-2022)
The following users liked this post:
1983ScarabIII (10-09-2022)
