30' Skater Project Let the Journey Begin
#101
Skater Brother
Platinum Member
#102
Registered
Thread Starter
#103
Registered
Thread Starter
Aft compartment upgrades
Finally got my Eddie Marine anodized fender holders. Also had ordered fender covers red/blue for each hull side to match fenders and 4ea new Sea Suckers. Also added Lumitech 3 color LED strip lights.
Here is a few pics.
White Mode
[ATTACH=CONFIG]547165[/ATTACH]
Red Mode
[ATTACH=CONFIG]547166[/ATTACH]
Blue Mode
[ATTACH=CONFIG]547167[/ATTACH]
Lastly raised motors to 2/18" above bottom and replaced oil injection tank valve on both engines.
Unfortunaely will not get to run it again until after the boat show.
Here is a few pics.
White Mode
[ATTACH=CONFIG]547165[/ATTACH]
Red Mode
[ATTACH=CONFIG]547166[/ATTACH]
Blue Mode
[ATTACH=CONFIG]547167[/ATTACH]
Lastly raised motors to 2/18" above bottom and replaced oil injection tank valve on both engines.
Unfortunaely will not get to run it again until after the boat show.
#105
Finally got my Eddie Marine anodized fender holders. Also had ordered fender covers red/blue for each hull side to match fenders and 4ea new Sea Suckers. Also added Lumitech 3 color LED strip lights.
Here is a few pics.
White Mode
[ATTACH=CONFIG]547165[/ATTACH]
Red Mode
[ATTACH=CONFIG]547166[/ATTACH]
Blue Mode
[ATTACH=CONFIG]547167[/ATTACH]
Lastly raised motors to 2/18" above bottom and replaced oil injection tank valve on both engines.
Unfortunaely will not get to run it again until after the boat show.
Here is a few pics.
White Mode
[ATTACH=CONFIG]547165[/ATTACH]
Red Mode
[ATTACH=CONFIG]547166[/ATTACH]
Blue Mode
[ATTACH=CONFIG]547167[/ATTACH]
Lastly raised motors to 2/18" above bottom and replaced oil injection tank valve on both engines.
Unfortunaely will not get to run it again until after the boat show.
#106
Platinum Member
Platinum Member
Finally got my Eddie Marine anodized fender holders. Also had ordered fender covers red/blue for each hull side to match fenders and 4ea new Sea Suckers. Also added Lumitech 3 color LED strip lights.
Here is a few pics.
White Mode
[ATTACH=CONFIG]547165[/ATTACH]
Red Mode
[ATTACH=CONFIG]547166[/ATTACH]
Blue Mode
[ATTACH=CONFIG]547167[/ATTACH]
Lastly raised motors to 2/18" above bottom and replaced oil injection tank valve on both engines.
Unfortunaely will not get to run it again until after the boat show.
Here is a few pics.
White Mode
[ATTACH=CONFIG]547165[/ATTACH]
Red Mode
[ATTACH=CONFIG]547166[/ATTACH]
Blue Mode
[ATTACH=CONFIG]547167[/ATTACH]
Lastly raised motors to 2/18" above bottom and replaced oil injection tank valve on both engines.
Unfortunaely will not get to run it again until after the boat show.
#107
Registered
Thread Starter
#108
Platinum Member
Platinum Member
after looking at the pics again I see its not much difference... Ill take one and post this afternoon. My batteries are mounted as far forward as possible...have 3 of them (I added one just for the stereo, I know, I know, weight kills lol.).
#109
Registered
Platinum Member
Join Date: Dec 2013
Location: East Texas Waterfront- running errands if anyone asks
Posts: 903
Likes: 0
Received 1 Like
on
1 Post
I'll leave it to Ron to tell me how to do that...
Last edited by Flightplan; 11-02-2015 at 10:23 AM.
#110
I'm planning on doing the same thing. I want two light weight lithium's for starting and a large deep cycle that I can remove easy, but leave installed for those recreational days when I'm not worried about the weight.
I'll leave it to Ron to tell me how to do that...
I'll leave it to Ron to tell me how to do that...
Have you found something that out performed this or is significantly lighter?
I find its much easier to reduce weight by jettisoning passengers.