28 porpusing BAD!!!!!
#1
Registered
Thread Starter
![Default](/forums/images/icons/icon1.gif)
My brother in-law bought a 2001 28 Sonic with 6.2L small blocks. The problem is that at cruise 3000rpm the boat will not settle down, he has tuck the drives almost all the way in and run the tabs down which is killimg the fuel mileage and speed. Props are 24 Bravos and has also tried 23 mirages doesnt seem to matter that much.
Solution thought to put a drive space in, thinking that the props are to far out of the water and are causing this.
Has anyone had good or bad results???
Solution thought to put a drive space in, thinking that the props are to far out of the water and are causing this.
Has anyone had good or bad results???
#2
Platinum Member
![](https://www.offshoreonly.com/forums/images/icons/platinum_member_star.gif)
![Default](/forums/images/icons/icon1.gif)
Not sure on the 28 but Prowler added a spacer to his 26' add it didn't help. I assume at higher speeds the porpoising goes away? Does he have a notched hull ? I rather doubt that the drives are to high but I'm not familiar with the 28. Steve
#3
Registered
Thread Starter
![Default](/forums/images/icons/icon1.gif)
Yes, if he runs the boat up towards 4500rpm it goes away some but still has some tab. Just cant cruise at all, the ride just sucks.
#4
Charter Member #1472
![](https://www.offshoreonly.com/forums/images/icons/charter_member_star.gif)
![Default](/forums/images/icons/icon1.gif)
well i put the 1" spacer in like steve said,didn't help anything,the only thing it did was made it harder to get on plane,lots of throttle.i faxed dollar last year,no response,just like you bought a used boat when i've had mine since new.the only thing i can think of is the drive is too deep,i'm keeping my eyes open for a shorty drive.if i'm up over 50 mph the boat runs fine,good thing with the upgade on the horsepower i can run 55 mph at 3500 rpm's with a non-labbed 30 pitch bravo-1 4-blade.the 28 might be a total different animal with twins and more weight,goodluck,dave
#5
Registered
Join Date: Jul 2003
Posts: 181
Likes: 0
Received 0 Likes
on
0 Posts
![Default](/forums/images/icons/icon1.gif)
I have had positive results running a lot of down tab and trimming the drive out. I can run 3200 rpm with min porpusing. Took me awhile to get the boat trimmed correctly but you can get it to almost stop.
#6
Registered
Thread Starter
![Default](/forums/images/icons/icon1.gif)
We can get it to stop also by alot of tab. I have never owned a boat that I could not cruise at 3000rpm/ 40 mph and constantly have to have that much tab. Something is wrong a boat should not do this. The speed is cut dramatically when the tabs have to come down.
Is the boat not balanced very well? All I know is if he cant fix the problem after this year the boat is forsale.
Is the boat not balanced very well? All I know is if he cant fix the problem after this year the boat is forsale.
#8
![Default](/forums/images/icons/icon1.gif)
Try running a set of Hydromotive's They will give you more stern lift. Where the Bravo's will give you more bow lift. Talk to Julie she will be able to help you.
#9
Charter Member #1472
![](https://www.offshoreonly.com/forums/images/icons/charter_member_star.gif)
![Default](/forums/images/icons/icon1.gif)
i try'd a hydromotive on mine,the prop felt real heavy and didn't do anything to help anything,after 10 minutes on the boat,prop came off and sold it,the only thing that seems to help is a bravo 1 4-blade at lower speeds,higher speeds and all out running a 3-blade mirage works real well.dave