Y2K/Arneson
#21
Registered
RIK the new bottom is introducing some more air to the bottom to free it up abit. The idea was not to fly the boat on the last 2 feet of the boat like a hydrosteam, That would be real bad in rough water, but to free up the bottom keeping some lenght in the water so it can run fast a stable in rough water. Although I havent been in a new one YET!
As far as steering the Arneson has the same turning radious as the bravo lock to lock, say 90* ? I know the props pretty far off the back . And going fast I see it a plus but around the dock I see a minus. For Gary it would be like docking a 35 footer with a single ! Wind catching the bow ! Breakout the bumpers ! OUCH
As far as steering the Arneson has the same turning radious as the bravo lock to lock, say 90* ? I know the props pretty far off the back . And going fast I see it a plus but around the dock I see a minus. For Gary it would be like docking a 35 footer with a single ! Wind catching the bow ! Breakout the bumpers ! OUCH
#22
Registered
RIK the new bottom is introducing some more air to the bottom to free it up abit. The idea was not to fly the boat on the last 2 feet of the boat like a hydrosteam, That would be real bad in rough water, but to free up the bottom keeping some lenght in the water so it can run fast a stable in rough water. Although I havent been in a new one YET!
As far as steering the Arneson has the same turning radious as the bravo lock to lock, say 90* ? I know the props pretty far off the back . And going fast I see it a plus but around the dock I see a minus. For Gary it would be like docking a 35 footer with a single ! Wind catching the bow ! Breakout the bumpers ! OUCH
As far as steering the Arneson has the same turning radious as the bravo lock to lock, say 90* ? I know the props pretty far off the back . And going fast I see it a plus but around the dock I see a minus. For Gary it would be like docking a 35 footer with a single ! Wind catching the bow ! Breakout the bumpers ! OUCH
#23
arneson-industries.com
Offshoreonly Advertiser
I am sorry, but I cannot follow the logic that the drive being longer makes the boat more difficult to dock in the wind when the drive is below the water line.
The boat size does not change, and anything under the water is not affected by the wind.
In fact, the longer the drive, the more mechanical leverage the drive has and hence the reason that my drives are docking and steering better than their I/O counterparts.
As for propeller centerline, with a surface drive, the propeller shaft will be at the water level, or around 4" higher than it currently is with this Bravo setup.
The engine would stay in its same location, I do not know the center distance between a Bravo input/output so I do not know where it currently resides.
But, our standoff box is the starting point in our install and it mounts in the area where the notch is so that is what I am referring to when looking at the photos.
The boat size does not change, and anything under the water is not affected by the wind.
In fact, the longer the drive, the more mechanical leverage the drive has and hence the reason that my drives are docking and steering better than their I/O counterparts.
As for propeller centerline, with a surface drive, the propeller shaft will be at the water level, or around 4" higher than it currently is with this Bravo setup.
The engine would stay in its same location, I do not know the center distance between a Bravo input/output so I do not know where it currently resides.
But, our standoff box is the starting point in our install and it mounts in the area where the notch is so that is what I am referring to when looking at the photos.
#24
VIP Member
VIP Member
As for propeller centerline, with a surface drive, the propeller shaft will be at the water level, or around 4" higher than it currently is with this Bravo setup.
The engine would stay in its same location, I do not know the center distance between a Bravo input/output so I do not know where it currently resides.
The engine would stay in its same location, I do not know the center distance between a Bravo input/output so I do not know where it currently resides.
__________________
Patrick
Patrick
#29
arneson-industries.com
Offshoreonly Advertiser
I am not certain of the power, I think it had somewhere between 1000-1200.
Know motor made over 1250 on the dyno but I do not know how much he took out of it.
Know motor made over 1250 on the dyno but I do not know how much he took out of it.
#30
VIP Member
VIP Member