Bravo Transom assembly complete bell housing back
02-16-2015, 08:34 AM
#1
Registered
Thread Starter
Bravo Transom assembly complete bell housing back
Complete Bravo Transom Assembly with Inner Transom Plate, Bellhousing, and Coupler, Trim hoses and wiring.. Fresh water.. Serial #00420648
It is missing the pins that I would call the "swivel pins" (the ones that go through the ring and are behind the trim sensors)
This stuff came off of a fresh water 22 Velocity I picked up a while back.. I planned to use this stuff, but could use the extra cash over parts at the current time.. The boat needs some transom work so I pretty much just removed what you see, and gave it about 10 min of soap & water..
$950.00 takes it all... This can either be picked up here at my shop, or I will safely package it all up and take it to UPS for no cost (just the actual shipping cost)
I mentioned that the swivel pins are missing above, If I find them in the boat someplace I will gladly toss them in.. The only other things I can think of are 1 of the corners on the Bellhousing where I assume Merc. uses for shipping is snapped off.. I've seen several of these like that, and those are mounts that are completely unused and have no effect whatsoever.. Also the coupler is missing one grease zerk... You can see any of this in the photos, however I always try my absolute best to represent my stuff as accurately as possible..
My PM box is usually full so please email: littledcsrodshop (at) comcast (dot) net
It is missing the pins that I would call the "swivel pins" (the ones that go through the ring and are behind the trim sensors)
This stuff came off of a fresh water 22 Velocity I picked up a while back.. I planned to use this stuff, but could use the extra cash over parts at the current time.. The boat needs some transom work so I pretty much just removed what you see, and gave it about 10 min of soap & water..
$950.00 takes it all... This can either be picked up here at my shop, or I will safely package it all up and take it to UPS for no cost (just the actual shipping cost)
I mentioned that the swivel pins are missing above, If I find them in the boat someplace I will gladly toss them in.. The only other things I can think of are 1 of the corners on the Bellhousing where I assume Merc. uses for shipping is snapped off.. I've seen several of these like that, and those are mounts that are completely unused and have no effect whatsoever.. Also the coupler is missing one grease zerk... You can see any of this in the photos, however I always try my absolute best to represent my stuff as accurately as possible..
My PM box is usually full so please email: littledcsrodshop (at) comcast (dot) net
Last edited by littledcsrodshop; 02-16-2015 at 08:59 AM.
02-16-2015, 08:49 AM
#3
Registered
Thread Starter
I'll add that none of this stuff with the exception of the backside of the coupler has had any paintwork.. The coupler has some light surface rust due to it sitting face down in the back of the boat when I got it, so I stripped it with a d/a and coated it good with satin black..
02-21-2015, 03:34 AM
#6
Registered
Thread Starter
Those that are trying to send me a PM my box is full...
Please send me an email, respond here , shoot me a txt, or get me your info
4 two three - 7 four four - 4 one nine three
Please send me an email, respond here , shoot me a txt, or get me your info
4 two three - 7 four four - 4 one nine three
02-25-2015, 03:10 PM
#9
Registered
Thread Starter
I know this is a boat forum, but I would consider from partial to full trades on somewhat higher end Acoustic guitars such as Gibson, Martin, Taylor, ect... I would also consider a nice Telecaster or Les Paul as well..
