Gravity bleed trailer brakes
#1
Gold Member
Gold Member
Thread Starter
Gravity bleed trailer brakes
Pretty sure my trailer brakes just need to be bled. I saw this video. http://www.youtube.com/watch?v=XVq7sAFJTpI
Seems pretty simple. Do you think this will work with trailer brakes?
Seems pretty simple. Do you think this will work with trailer brakes?
#2
Registered
Join Date: Aug 2013
Location: Greenwell Springs, Louisiana
Posts: 128
Likes: 0
Received 0 Likes
on
0 Posts
Top off the fluid in the master cylinder and make sure the master cylinder is higher than the bleed ports.
You might need to actuate the cylinder a couple of times if you don't get any flow at first, but other than that, just make sure you keep the cap off the master cylinder and keep it full while it bleeds.
You might need to actuate the cylinder a couple of times if you don't get any flow at first, but other than that, just make sure you keep the cap off the master cylinder and keep it full while it bleeds.
#3
Registered
Join Date: Aug 2006
Location: Ontario, OH
Posts: 2,465
Likes: 0
Received 0 Likes
on
0 Posts
I didn't watch the video but I used to gravity feed my brakes. I just used a tube and a pop bottle, sucked on the tube to get it going and when I saw the fluid (clear tube obviously) draped it over a bunk and let it gravity bleed into the pop bottle for awhile. I have surge brakes with a Titan/Dico actuator with discs.
I have a gast vacuum pump I use now with a catch chamber.
I have a gast vacuum pump I use now with a catch chamber.
#4
Registered
[ATTACH=CONFIG]523885[/ATTACH] $20.00 Home depot pump up spayer, extra master cylinder cap. Little modification, fill with brake fliud and pump up. While cap is screwed on master of course.
#5
Forum Regulator
VIP Member
I don't know for certain that gravity feed will work with trailer brakes, but that all depends on the routing of your brake lines. If you have any "loops or humps" in your brake line routing that are higher than your bleeder valves, I would think air would trap in there sans pressurizing all the way against a slightly opened bleeder.
I did not know about those Russel Bleeder Valves. Good to know.
For those with EoH, you can use the manual activation button in the truck (with a second person) to push fluid through the system.
I too have a pump system as shown above, but I bought it many years ago; as it was specifically a 1-man bleeder system made for such.
I did not know about those Russel Bleeder Valves. Good to know.
For those with EoH, you can use the manual activation button in the truck (with a second person) to push fluid through the system.
I too have a pump system as shown above, but I bought it many years ago; as it was specifically a 1-man bleeder system made for such.
#9
Gold Member
Gold Member
Thread Starter
Ahhhh..... I just remembered that I have one of these collecting dust in my attic. This should do the trick. I haven't used it since I got a motor with a drain hose attached to the pan.
[ATTACH=CONFIG]523921[/ATTACH]
[ATTACH=CONFIG]523921[/ATTACH]
#10
Registered
Join Date: Oct 2011
Location: Perry Lake, KS Lake of Ozarks
Posts: 390
Likes: 0
Received 0 Likes
on
0 Posts
I like this kit from HF. http://www.harborfreight.com/brake-f...der-92924.html
The reservoir bottle is nice since you don't have to worry about sucking air or refilling.
I know there are ways to rig up stuff but this is too cheap and easy to grab and go!
The reservoir bottle is nice since you don't have to worry about sucking air or refilling.
I know there are ways to rig up stuff but this is too cheap and easy to grab and go!