pro charger
09-30-2008, 05:22 PM
#1
Pirate of the Chesapeake
Gold MemberThread Starter
Join Date: Aug 2006
Location: North Point Creek, Md.
Posts: 4,330
Likes: 0
Received 0 Likes
on
0 Posts
pro charger
I have posted before but only get feedback for big block pro chargers. I am looking for a procharger set up ( used ) for a 350 small block mpi motor. Thanks JOHN
09-30-2008, 05:33 PM
#2
Registered
Join Date: Mar 2008
Location: monterey, ca
Posts: 150
Likes: 0
Received 0 Likes
on
0 Posts
You could probably use an M1SC and buy a small block bracket. Besides, depends on how the motor is setup to calibrate the thing properly..
I have one I may part with.. (M1 SC with AWIC) you would need the SB Bracket from ATI.. Send a PM if interested..
I have one I may part with.. (M1 SC with AWIC) you would need the SB Bracket from ATI.. Send a PM if interested..
10-03-2008, 02:36 AM
#4
Registered
Join Date: Mar 2008
Location: monterey, ca
Posts: 150
Likes: 0
Received 0 Likes
on
0 Posts
M1 SC Procharger
John,
I tried sending you a PM but your box is full.. So, I posted it here instead..
I have an M1 SC with an air to water intercooler. I think I have the fuel pressure regulator as well, and I have a crank pulley for a big block. I also have a bracket for a fuel injected serpentine drive big block, and hoses etc. The parts are in boxes in back of my garage, and are in very good condition. I think $2500 would be fair for all of the stuff.
If you have the small block bracket, then you just need to bolt up, recalibrate your ECU, plumb the cooler lines, and fuel, and you are done except for fine tuning..
The M1SC is the self contained blower, but can be converted to the engine lubricated type with a pressure feed oil line to the blower from the engine and a drain to the oil pan.
Sorry or the delay in responding, but send me an email at [email protected] for a faster response.
If you are intersted, please let me know. I can send you some more pictures. The pic attached has more than just the SC stuff, I have sold the intake, and I am not selling the big red Aeromotive fuel pump. JUST the SC, Cooler, lines, and related SC items in the picture for $2500.
Others are asking $3500 for the same stuff... I'm not using the procharger, and I switched the configuration of the motor the SC was to be used on, and it is going to be built with twin turbos instead. I have 5 engines, and various parts, and should clean my garage if you know what I mean...... Once you get the items, you would be responsible for calling ATI and transferring the serial # to your name from mine so you can get access to tech support etc..
Thanks,
Richard
I tried sending you a PM but your box is full.. So, I posted it here instead..
I have an M1 SC with an air to water intercooler. I think I have the fuel pressure regulator as well, and I have a crank pulley for a big block. I also have a bracket for a fuel injected serpentine drive big block, and hoses etc. The parts are in boxes in back of my garage, and are in very good condition. I think $2500 would be fair for all of the stuff.
If you have the small block bracket, then you just need to bolt up, recalibrate your ECU, plumb the cooler lines, and fuel, and you are done except for fine tuning..
The M1SC is the self contained blower, but can be converted to the engine lubricated type with a pressure feed oil line to the blower from the engine and a drain to the oil pan.
Sorry or the delay in responding, but send me an email at [email protected] for a faster response.
If you are intersted, please let me know. I can send you some more pictures. The pic attached has more than just the SC stuff, I have sold the intake, and I am not selling the big red Aeromotive fuel pump. JUST the SC, Cooler, lines, and related SC items in the picture for $2500.
Others are asking $3500 for the same stuff... I'm not using the procharger, and I switched the configuration of the motor the SC was to be used on, and it is going to be built with twin turbos instead. I have 5 engines, and various parts, and should clean my garage if you know what I mean...... Once you get the items, you would be responsible for calling ATI and transferring the serial # to your name from mine so you can get access to tech support etc..
Thanks,
Richard
