Offshoreonly.com
0 2023/09/20 18:33:26
0 2023/09/20 18:33:23
Short hub prop cone with castle thingyThrust washer/fishing line cutter
Short hub prop cone with castle thingyThrust washer/fishing line cutter
0 2023/09/20 17:36:50
0 2023/09/20 17:36:48
0 2023/09/20 17:36:46
0 2023/09/18 15:37:13
And i would scroll cut them round. A square cut board has only the strenght of it's smallest part, i.e a 2x8 notched out
And i would scroll cut them round. A square cut board has only the strenght of it's smallest part, i.e a 2x8 notched out
0 2023/09/18 15:18:44
0 2023/09/18 15:07:24
0 2023/09/18 15:07:01
0 2023/09/18 15:05:33
0 2023/09/18 15:05:29
Congratulations mike and johnny, go team moderation !
Congratulations mike and johnny, go team moderation !
0 2023/09/17 18:04:45
0 2023/08/29 19:14:35
0 2023/07/25 07:14:30
0 2023/07/12 11:18:57
Even as a hobby, all the extra grinding is worth it. Easier to fit and bed down the new stringers, for sure a better bond and a better looking job to be proud of.
Even as a hobby, all the extra grinding is worth it. Easier to fit and bed down the new stringers, for sure a better bond and a better looking job to be proud of.
0 2023/07/10 14:34:13
When your grinding
When your grinding
0 2023/07/10 14:31:38
0 2023/07/10 14:31:34
Fiberglass dust.
Fiberglass dust.
0 2023/07/10 14:30:28
0 2023/07/10 14:30:24
Here is the part number
Here is the part number
0 2023/06/12 07:57:04
It diagnoses ; improper gimbal ring height. improper/ sunken rear engine mounts. Mis-aligned gimbal bearing. Engine alignment issues.
It diagnoses ; improper gimbal ring height. improper/ sunken rear engine mounts. Mis-aligned gimbal bearing. Engine alignment issues.
0 2023/06/12 07:57:01
in my opinion, this is the alignment tool you need. It fits into the transom assembly and on the alignment shaft tool. It wont sit flush unless the engine-gimbal bearing and outdrive bellhousing are all in alignment.
in my opinion, this is the alignment tool you need. It fits into the transom assembly and on the alignment shaft tool. It wont sit flush unless the engine-gimbal bearing and outdrive bellhousing are all in alignment.
0 2023/06/12 07:56:56
0 2023/06/12 07:56:53
0 2023/06/12 07:56:50
0 2023/06/12 07:56:47
Very poor 3d attempt of horizontal stiffener.
Very poor 3d attempt of horizontal stiffener.
0 2023/04/19 17:36:28
Transom cross section
Transom cross section
0 2023/04/19 17:36:21
0 2023/04/19 17:36:13
0 2023/04/05 17:47:34
0 2023/04/05 17:47:26
0 2023/03/23 18:21:33
0 2023/03/16 07:42:06
0 2023/03/16 07:30:38
0 2023/03/16 07:30:35
0 2023/03/16 07:30:33
0 2023/03/16 07:30:31
0 2023/03/16 07:30:28
You can see where the water leaves the hull and the k planes are clearly visible.
You can see where the water leaves the hull and the k planes are clearly visible.
0 2023/03/16 07:30:25
Thats how much was cut off the ring to stop chinewalk. The 25 liked nuetral trim and needed the ring cut down , the 27 wanted lots of trim and barely had chinewalk, it would never come on plane after that much ring cut off. Calm water like pictured, 25 top was 73.4, calm water like pictured, 27 was over 74
Thats how much was cut off the ring to stop chinewalk. The 25 liked nuetral trim and needed the ring cut down , the 27 wanted lots of trim and barely had chinewalk, it would never come on plane after that much ring cut off. Calm water like pictured, 25 top was 73.4, calm water like pictured, 27 was over 74
0 2023/03/16 07:30:22
Advertising | Cookie Policy | Privacy Statement | Terms of Service | Manage Preferences | Your Privacy Choices
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.