Offshoreonly.com
0 2019/02/25 18:38:37
0 2019/02/25 18:38:37
As of now (before the Arnesons snow up) this is where the motors set. The broomstick across the top is representing the hatch. Some different scoops are probably in the order as I would like to get some different flame arrestors
As of now (before the Arnesons snow up) this is where the motors set. The broomstick across the top is representing the hatch. Some different scoops are probably in the order as I would like to get some different flame arrestors
0 2019/02/25 18:38:37
0 2019/02/25 18:38:37
Harper half the barn off so the rest of the toys
Harper half the barn off so the rest of the toys
0 2019/02/25 18:38:37
0 2019/02/25 18:38:36
0 2019/02/25 18:38:35
Added some lights above the bilge so I could see a bit better!
Added some lights above the bilge so I could see a bit better!
0 2019/02/25 18:38:35
0 2019/02/25 18:38:34
0 2019/02/25 18:38:33
0 2019/02/25 18:38:33
Here’s where the project got a little more real and time consuming...(because the trailer was a breeze LOL not!)
Here’s where the project got a little more real and time consuming...(because the trailer was a breeze LOL not!)
0 2019/02/25 18:38:32
0 2019/02/25 18:38:32
0 2019/02/25 18:38:26
0 2019/02/25 18:38:07
Sanded flat
Sanded flat
0 2019/02/25 18:23:16
New piece tacked in
New piece tacked in
0 2019/02/25 18:23:15
Rear motor mount clearance to slide closer to the tunnel
Rear motor mount clearance to slide closer to the tunnel
0 2019/02/25 18:23:14
Clearance for tunnel on the front motor mounts
Clearance for tunnel on the front motor mounts
0 2019/02/25 18:23:14
Fully welded (1/16” dual shield)
Fully welded (1/16” dual shield)
0 2019/02/25 18:23:14
One side of mounts done!
One side of mounts done!
0 2019/02/25 18:23:10
After cutting a bit out the mount out I wanted to fill some of it back in to regain strength
After cutting a bit out the mount out I wanted to fill some of it back in to regain strength
0 2019/02/25 18:23:10
Built a jig to ensure the mounts were true with eachother and still maintained a 9” offset in height difference
Built a jig to ensure the mounts were true with eachother and still maintained a 9” offset in height difference
0 2019/02/25 18:23:10
Both mounts setting on jig
Both mounts setting on jig
0 2019/02/25 18:23:10
Taking an inch and three quarters out to move inboard
Taking an inch and three quarters out to move inboard
0 2019/02/25 18:23:00
And the clearance cut out to move over
And the clearance cut out to move over
0 2019/02/25 18:22:36
0 2019/02/25 18:20:51
0 2019/02/25 18:20:50
0 2019/02/25 18:20:49
0 2019/02/25 18:20:48
0 2019/02/25 18:20:47
0 2019/02/25 16:05:58
0 2019/02/25 16:05:57
0 2019/02/25 16:05:57
0 2019/02/25 16:05:57
0 2019/02/25 16:05:57
0 2019/02/25 16:05:57
0 2019/02/25 16:05:57
0 2019/02/25 16:05:56
0 2019/02/25 16:05:56
Advertising | Cookie Policy | Privacy Statement | Terms of Service | Manage Preferences | Your Privacy Choices
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.